Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301742 REAR VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the navigation receiver assembly judges that the signals or signal lines between the navigation receiver assembly, and the rear television camera assembly are not normal as a result of its self check.

DTC No. DTC Detection Condition Trouble Area
C1622 Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly



WIRING DIAGRAM

E449335E01
0.406,2.708 2.49,2.885 2.083,0.177 10 false Navigation Receiver Assembly 5.146,2.281 5.49,2.438 0.344,0.156 10 false V14 5.146,2.448 6.646,2.76 1.5,0.313 10 false Rear Television Camera Assembly 5.365,0.646 5.656,0.802 0.292,0.156 10 false CB+ 5.365,1.042 5.656,1.198 0.292,0.156 10 false CV+ 5.365,1.438 5.625,1.594 0.26,0.156 10 false CV- 5.365,1.844 5.792,2 0.427,0.156 10 false CGND 1.344,0.646 1.719,0.885 0.375,0.24 10 false CA+ 1.427,1.042 1.708,1.271 0.281,0.229 10 false V+ 1.458,1.438 1.667,1.646 0.208,0.208 10 false V- 1.219,1.823 1.646,1.979 0.427,0.156 10 false CGND 1.25,2.219 1.656,2.375 0.406,0.156 10 false GND1 1.729,0.646 2.083,0.802 0.354,0.156 10 false L172 1.729,1.042 2.083,1.198 0.354,0.156 10 false L172 1.729,1.438 2.083,1.594 0.354,0.156 10 false L172 1.729,1.844 2.083,2 0.354,0.156 10 false L172 5.188,0.563 5.281,0.719 0.094,0.156 10 false 6 5.188,0.958 5.281,1.115 0.094,0.156 10 false 3 5.188,1.344 5.281,1.5 0.094,0.156 10 false 2 5.188,1.74 5.281,1.896 0.094,0.156 10 false 5 1.74,2.24 2.104,2.396 0.365,0.156 10 false L171 3.729,1.604 3.875,1.76 0.146,0.156 10 false * 0.406,4.323 1.188,4.479 0.781,0.156 10 false *: Shielded 1.813,0.448 2.135,0.604 0.323,0.156 10 false 11 1.813,0.844 2.135,1 0.323,0.156 10 false 12 1.823,1.24 2.146,1.396 0.323,0.156 10 false 24 1.813,1.646 2.135,1.802 0.323,0.156 10 false 23 1.844,2.042 2.167,2.198 0.323,0.156 10 false 7

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the L172 navigation receiver assembly connector.


b.

Disconnect the V14 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L172-11 (CA+) - V14-6 (CB+) Always Below 1 Ω
L172-12 (V+) - V14-3 (CV+) Always Below 1 Ω
L172-24 (V-) - V14-2 (CV-) Always Below 1 Ω
L172-23 (CGND) - V14-5 (CGND) Always Below 1 Ω
L172-11 (CA+) or V14-6 (CB+) - Body ground Always 10 kΩ or higher
L172-12 (V+) or V14-3 (CV+) - Body ground Always 10 kΩ or higher
L172-24 (V-) or V14-2 (CV-) - Body ground Always 10 kΩ or higher
L172-23 (CGND) or V14-5 (CGND) - Body ground Always 10 kΩ or higher




OK

2.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Reconnect the L172 navigation receiver assembly connector.


b.
U191426E01
0.783,1.469 1.258,1.864 false 1.368,2.75 1.268,2.055 false 0.377,1.37 0.727,1.538 0.350,0.168 10 CA+ 1.105,2.793 1.657,2.949 0.552,0.156 10 CGND 1.555,0.783 1.918,0.939 0.363,0.156 10 L172 0.085,0.05 0.321,0.219 0.237,0.169 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L172-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L172-11 (CA+) - L172-23 (CGND) Power switch on (ACC) 5.5 to 7.05 V


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)



OK

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY

NG

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
a.

Reconnect the V14 rear television camera assembly connector.


b.
U191428E01
0.774,0.761 1.125,1.107 false 2.187,4.119 1.84,3.62 false 1.995,4.172 2.512,4.328 0.517,0.156 10 GND1 0.486,0.658 0.723,0.827 0.237,0.169 10 V+ 1.545,0.273 1.883,0.486 0.337,0.213 10 L172 1.547,2.411 1.885,2.624 0.337,0.213 10 L171 0.069,0.035 0.305,0.204 0.237,0.169 10 *a

Using an oscilloscope, check the waveform of the rear television camera assembly.

Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)

E361811E01
1,2.333 1.167,2.333 1.167,2.333 1.26,1.781 false 1.667,2.333 1.5,2.333 1.5,2.333 1.365,1.677 false 4.5,2.25 4.667,2.25 4.667,2.25 4.729,1.635 false 5.167,2.25 5,2.25 5,2.25 4.865,1.563 false 0.448,0.292 0.76,0.49 0.313,0.198 10 false *a 3.99,0.219 4.302,0.417 0.313,0.198 10 false *b 0.5,1.219 0.865,1.417 0.365,0.198 10 false GND 0.813,2.25 1.125,2.448 0.313,0.198 10 false *c 1.698,2.26 2.01,2.458 0.313,0.198 10 false *d 3.948,1.229 4.313,1.427 0.365,0.198 10 false GND 5.208,2.167 5.521,2.365 0.313,0.198 10 false *d 4.323,2.167 4.635,2.365 0.313,0.198 10 false *c

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal L172-12 (V+) - L171-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).



Text in Illustration
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform



OK

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY