Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › from 2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM U

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  TERMINALS OF ECU  


PARKING ASSIST ECU


E449982N01
3.188,0.844 3.615,1.135 0.427,0.292 10 false L65 5.49,0.833 5.917,1.125 0.427,0.292 10 false L64

a.

Disconnect the L64 parking assist ECU connector.


b.

Measure the voltage and resistance of each terminal of the wire harness side connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L64-1 (+B) - L64-4 (GND1) GR - W-B Power source signal Power switch off 11 to 14 V
L64-4 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
L64-8 (IG) - L64-4 (GND1) SB - W-B IG power source signal Power switch on (IG) 11 to 14 V
L64-9 (ACC) - L64-4 (GND1) P - W-B ACC power source signal Power switch on (ACC) 11 to 14 V
L64-11 (TX+) - L64-10 (TX-) B - W AVC-LAN communication signal - -

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the L64 parking assist ECU connector.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-1 (CSB3) - L64-4 (GND1) G - W-B Power source to ultrasonic sensor Power switch on (IG) 7.2 to 8.8 V
L65-2 (CSG3) - L64-4 (GND1) P - W-B Ultrasonic sensor ground Always Below 1 Ω
L65-8 (HO1) - L64-4 (GND1) SB - W-B Rear height control sensor signal output Power switch off Below 1 V
Power switch on (IG) 0.5 to 5.25 V
L65-9 (HI1) - L64-4 (GND1) L - W-B Rear height control sensor signal input Power switch off Below 1 V
Power switch on (IG) 0.5 to 5.25 V
L65-14 (CB+) - L64-4 (GND1) W - W-B Power source to rear television camera Power switch on (ACC) 5.5 to 7.05 V
L65-15 (CV+) - L64-4 (GND1) R - W-B Display signal (NTSC) input Power switch on (IG)
Reverse (R) selected
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 1)
Power switch on (IG)
Reverse (R) selected
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
L65-16 (NS+) - L64-4 (GND1) G - W-B Display signal (NTSC) output Power switch on (IG)
Reverse (R) selected
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 3)
Power switch on (IG)
Reverse (R) selected
Camera lens covered, displaying an image
Pulse generation
(Refer to waveform 4)
L65-17 (NS-) - L64-4 (GND1) R - W-B Display signal (NTSC) ground Always Below 1 V
L65-18 (NSG) - L64-4 (GND1) Shield - W-B Display signal (NTSC) ground (shield) Always Below 1 V
L65-19 (LIN3) GR Ultrasonic sensor signal input and output - -
L65-26 (ISSW) - L64-4 (GND1) R - W-B Parking assist pre support signal input Power switch on (IG)
Parking assist pre support switch assembly pushed in
Below 1 V
Power switch on (IG)
Parking assist pre support switch assembly not pushed
4.75 to 5.25 V
L65-27 (HBL+) - L64-4 (GND1) P - W-B Rear height control sensor power supply Power switch off Below 1 V
Power switch on (IG) 4.75 to 5.25 V
L65-28 (HB+) - L64-4 (GND1) P - W-B Rear height control sensor power supply Power switch off Below 1 V
Power switch on (IG) 4.75 to 5.25 V
L65-29 (HGND) - Body ground Y - Body ground Rear height control sensor ground Always Below 1 Ω
L65-31 (HG1) - Body ground Y - Body ground Rear height control sensor ground Always Below 1 Ω
L65-37 (CGND) - L64-4 (GND1) Shield - W-B Rear television camera ground (shield) Always Below 1 V
L65-38 (CV-) - L64-4 (GND1) B - W-B Rear television camera ground Always Below 1 V
L65-39 (CANL) - L64-4 (GND1) L - W-B CAN communication signal - -
L65-40 (CANH) - L64-4 (GND1) B - W-B CAN communication signal - -

If the result is not as specified, the ECU may have a malfunction.


e.

Reference (Oscilloscope waveform):

E361811E01
1,2.333 1.167,2.333 1.167,2.333 1.26,1.781 false 1.667,2.333 1.5,2.333 1.5,2.333 1.365,1.677 false 4.5,2.25 4.667,2.25 4.667,2.25 4.729,1.635 false 5.167,2.25 5,2.25 5,2.25 4.865,1.563 false 0.448,0.292 0.76,0.49 0.313,0.198 10 false *a 3.99,0.219 4.302,0.417 0.313,0.198 10 false *b 0.5,1.219 0.865,1.417 0.365,0.198 10 false GND 0.813,2.25 1.125,2.448 0.313,0.198 10 false *c 1.698,2.26 2.01,2.458 0.313,0.198 10 false *d 3.948,1.229 4.313,1.427 0.365,0.198 10 false GND 5.208,2.167 5.521,2.365 0.313,0.198 10 false *d 4.323,2.167 4.635,2.365 0.313,0.198 10 false *c

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement Terminal L65-15 (CV+) - L64-4 (GND1)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement Terminal L65-15 (CV+) - L64-4 (GND1)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).



Text in Illustration
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform



f.

Reference (Oscilloscope waveform):

E361811E01
1,2.333 1.167,2.333 1.167,2.333 1.26,1.781 false 1.667,2.333 1.5,2.333 1.5,2.333 1.365,1.677 false 4.5,2.25 4.667,2.25 4.667,2.25 4.729,1.635 false 5.167,2.25 5,2.25 5,2.25 4.865,1.563 false 0.448,0.292 0.76,0.49 0.313,0.198 10 false *a 3.99,0.219 4.302,0.417 0.313,0.198 10 false *b 0.5,1.219 0.865,1.417 0.365,0.198 10 false GND 0.813,2.25 1.125,2.448 0.313,0.198 10 false *c 1.698,2.26 2.01,2.458 0.313,0.198 10 false *d 3.948,1.229 4.313,1.427 0.365,0.198 10 false GND 5.208,2.167 5.521,2.365 0.313,0.198 10 false *d 4.323,2.167 4.635,2.365 0.313,0.198 10 false *c

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


i.

Waveform 3(camera lens is not covered, displaying an image)

Item Content
Measurement Terminal L65-16 (NS+) - L64-4 (GND1)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



ii.

Waveform 4(camera lens is covered, blacking out the screen)

Item Content
Measurement Terminal L65-16 (NS+) - L64-4 (GND1)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Text in Illustration
*a Waveform 3 (camera lens not covered, displaying an image)
*b Waveform 4 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform




REAR TELEVISION CAMERA ASSEMBLY


U191283E02
3.479,0.167 3.76,0.344 0.281,0.177 10 false V14

a.

Disconnect the V14 rear television camera assembly connector.


b.

Measure the voltage of each terminal of the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V14-6 (CB+) - Body ground W - Body ground Power source Power switch on (ACC)
Reverse (R) selected
5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Measure the resistance of each terminal of the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V14-1 (CURT) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Reconnect the V14 rear television camera assembly connector.


e.

Measure the voltage and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V14-3 (CV+) - V14-2 (CV-) R - B Display signal (NTSC) output Power switch on (IG)
Reverse (R) selected
Camera lens not covered, displaying an image
Pulse generation
(Refer to waveform 5)
Power switch on (IG)
Reverse (R) selected
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 6)
V14-5 (CGND) - Body ground W-B - Body ground Shield ground Always Below 1 V

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


If the result is not as specified, the camera may have a malfunction.


f.

Reference (Oscilloscope waveform):

E361811E01
1,2.333 1.167,2.333 1.167,2.333 1.26,1.781 false 1.667,2.333 1.5,2.333 1.5,2.333 1.365,1.677 false 4.5,2.25 4.667,2.25 4.667,2.25 4.729,1.635 false 5.167,2.25 5,2.25 5,2.25 4.865,1.563 false 0.448,0.292 0.76,0.49 0.313,0.198 10 false *a 3.99,0.219 4.302,0.417 0.313,0.198 10 false *b 0.5,1.219 0.865,1.417 0.365,0.198 10 false GND 0.813,2.25 1.125,2.448 0.313,0.198 10 false *c 1.698,2.26 2.01,2.458 0.313,0.198 10 false *d 3.948,1.229 4.313,1.427 0.365,0.198 10 false GND 5.208,2.167 5.521,2.365 0.313,0.198 10 false *d 4.323,2.167 4.635,2.365 0.313,0.198 10 false *c

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


i.

Waveform 5 (camera lens is not covered, displaying an image)

Item Content
Measurement Terminal V14-3 (CV+) - V14-2 (CV-)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




ii.

Waveform 6 (camera lens is covered, blacking out the screen)

Item Content
Measurement Terminal V14-3 (CV+) - V14-2 (CV-)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).



Text in Illustration
*a Waveform 5 (camera lens not covered, displaying an image)
*b Waveform 6 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform





HEADLIGHT LEVELING ECU ASSEMBLY (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU)