Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH › from 2020.08
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301917 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY

a.
E409581C76
1.479,0.083 1.885,0.323 0.406,0.24 1.292,1.396 1.125,1.906 true 2.271,1.375 2.479,1.823 true 2.063,1.396 1.906,1.906 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.563,0.115 1.99,0.333 0.427,0.219 10 false A93 2.458,1.854 2.625,2.021 0.167,0.167 10 false B 0.958,1.917 1.375,2.104 0.417,0.188 10 false GND 1.844,1.906 2.01,2.073 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A93 stop light switch assembly connector.


b.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A93-7 (B) - A93-2 (GND) Always 11 to 14 V
A93-6 (B) - A93-2 (GND) Power switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A93-2 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.


c.

Connect the A93 stop light switch assembly connector.


d.
E409580C32
1.51,0.083 1.927,0.385 0.417,0.302 2.313,1.24 2.896,0.938 true 2.135,1.26 2.49,1.875 true 1.927,1.271 2.281,1.885 true 1.24,1.865 1.698,1.292 true 0.865,1.948 1.49,1.281 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.594,0.135 2.052,0.333 0.458,0.198 10 false A93 2.969,0.833 3.313,1.073 0.344,0.24 10 false OUT 2.552,1.823 2.896,2.063 0.344,0.24 10 false GND 2.281,1.906 2.438,2.104 0.156,0.198 10 false L 1.063,1.896 1.406,2.135 0.344,0.24 10 false ACC 0.76,1.917 0.917,2.115 0.156,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A93-1 (OUT) - A93-2 (GND) Brake pedal released 1.5 V or less
A93-1 (OUT) - A93-2 (GND) Brake pedal depressed 11 to 14 V
A93-3 (L) - A93-2 (GND) Brake pedal released 1.5 V or less
A93-3 (L) - A93-2 (GND) Brake pedal depressed 11 to 14 V
A93-4 (ACC) - A93-2 (GND) Always 11 to 14 V
A93-5 (L) - A93-2 (GND) Power switch on (IG), brake pedal not depressed 7.5 to 14 V
A93-5 (L) - A93-2 (GND) Power switch on (IG), brake pedal depressed 0 to 1.5 V


If the result is not as specified, replace the stop light switch assembly.