Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 2 Line for Short to GND (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Hybrid vehicle control ECU

·

ECM

·

Main body ECU (multiplex network body ECU)

·

Combination meter sub-assembly

·

Brake booster with master cylinder assembly (skid control ECU)

·

Spiral cable with sensor sub-assembly (steering angle sensor)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Airbag ECU assembly

·

Transmission control ECU assembly

·

Certification ECU (smart key ECU assembly)

·

Vehicle approaching speaker controller

·

No. 3 CAN junction connector

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



WIRING DIAGRAM

C443243E01
6.344,1.24 6.802,1.438 0.458,0.198 10 false ECM 6.01,1.24 6.469,1.438 0.458,0.198 10 false A57 6.406,0.563 6.865,0.76 0.458,0.198 10 false 120 Ω 5.865,0.208 6.323,0.406 0.458,0.198 10 false CANH 5.885,0.74 6.344,0.938 0.458,0.198 10 false CANL 5.615,0.208 6.073,0.406 0.458,0.198 10 false 13 5.688,0.75 5.927,1 0.24,0.25 10 false 5 4.052,0.313 4.51,0.51 0.458,0.198 10 false A67 4.052,0.833 4.51,1.031 0.458,0.198 10 false A67 4.135,0.646 4.375,0.896 0.24,0.25 10 false 7 4.115,0.115 4.354,0.365 0.24,0.25 10 false 1 2.604,3.885 4.729,4.219 2.125,0.333 10 false No. 1 CAN Junction Connector 2.938,0.313 3.396,0.51 0.458,0.198 10 false A67 2.948,0.844 3.406,1.042 0.458,0.198 10 false A67 2.906,2.188 3.365,2.385 0.458,0.198 10 false L132 2.906,2.719 3.365,2.917 0.458,0.198 10 false L132 4.021,3.198 4.479,3.396 0.458,0.198 10 false L132 4.021,3.667 4.479,3.865 0.458,0.198 10 false L132 3.021,0.667 3.26,0.917 0.24,0.25 10 false 8 3.021,0.125 3.26,0.375 0.24,0.25 10 false 2 1.354,0.219 1.813,0.417 0.458,0.198 10 false 37 1.344,0.698 1.802,0.896 0.458,0.198 10 false 38 0.833,0.302 1.292,0.5 0.458,0.198 10 false CA1H 0.844,0.844 1.302,1.042 0.458,0.198 10 false CA1L 0.094,1.24 0.552,1.438 0.458,0.198 10 false A58 0.396,1.24 2.583,1.667 2.188,0.427 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 0.427,3.146 2.073,3.656 1.646,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 0.073,3.146 0.531,3.344 0.458,0.198 10 false L201 0.823,2.146 1.281,2.344 0.458,0.198 10 false CANH 0.844,2.698 1.302,2.896 0.458,0.198 10 false CANL 1.302,2.083 1.76,2.281 0.458,0.198 10 false 14 1.323,2.594 1.781,2.792 0.458,0.198 10 false 13 2.979,2.5 3.438,2.698 0.458,0.198 10 false 11 3.021,1.979 3.479,2.177 0.458,0.198 10 false 5 4.125,3.021 4.583,3.219 0.458,0.198 10 false 6 4.094,3.479 4.552,3.677 0.458,0.198 10 false 12 2.677,8.417 4.802,8.75 2.125,0.333 10 false No. 2 CAN Junction Connector 0.396,5.698 1.354,6.146 0.958,0.448 10 false Power Steering ECU Assembly 0.104,5.698 0.563,5.896 0.458,0.198 10 false L54 0.802,4.771 1.26,4.969 0.458,0.198 10 false CANH 0.823,5.281 1.281,5.479 0.458,0.198 10 false CANL 1.323,4.667 1.781,4.865 0.458,0.198 10 false 1 1.313,5.177 1.771,5.375 0.458,0.198 10 false 7 2.938,5.281 3.396,5.479 0.458,0.198 10 false L95 2.927,4.771 3.385,4.969 0.458,0.198 10 false L95 3.021,4.583 3.479,4.781 0.458,0.198 10 false 2 3.01,5.104 3.469,5.302 0.458,0.198 10 false 3 4.052,4.365 4.51,4.563 0.458,0.198 10 false L94 4.063,4.875 4.521,5.073 0.458,0.198 10 false L94 4.135,4.167 4.594,4.365 0.458,0.198 10 false 5 4.135,4.688 4.594,4.885 0.458,0.198 10 false 4 2.927,7.74 3.385,7.938 0.458,0.198 10 false L95 2.938,7.198 3.396,7.396 0.458,0.198 10 false L95 3.01,7 3.469,7.198 0.458,0.198 10 false 5 3,7.542 3.458,7.74 0.458,0.198 10 false 6 0.813,7.208 1.271,7.406 0.458,0.198 10 false CANH 0.833,7.76 1.292,7.958 0.458,0.198 10 false CANL 1.302,7.115 1.76,7.313 0.458,0.198 10 false 11 1.302,7.635 1.76,7.833 0.458,0.198 10 false 12 0.375,8.156 1.927,8.583 1.552,0.427 10 false Air Conditioning Amplifier Assembly 0.104,8.156 0.563,8.354 0.458,0.198 10 false L17 4.042,7.729 4.5,7.927 0.458,0.198 10 false L95 4.052,7.208 4.51,7.406 0.458,0.198 10 false L95 4.083,7.01 4.542,7.208 0.458,0.198 10 false 11 4.073,7.552 4.531,7.75 0.458,0.198 10 false 12 5.615,7.083 6.073,7.281 0.458,0.198 10 false 18 5.604,7.635 6.063,7.833 0.458,0.198 10 false 17 5.854,7.208 6.313,7.406 0.458,0.198 10 false CA4H 5.865,7.771 6.323,7.969 0.458,0.198 10 false CA4L 5.146,8.146 5.604,8.344 0.458,0.198 10 false L192 5.521,8.146 7.021,8.615 1.5,0.469 10 false Central Gateway ECU (Network Gateway ECU) 4.052,5.833 4.51,6.031 0.458,0.198 10 false L94 4.052,5.302 4.51,5.5 0.458,0.198 10 false L94 4.052,5.104 4.51,5.302 0.458,0.198 10 false 14 4.063,5.635 4.521,5.833 0.458,0.198 10 false 13 5.865,5.323 6.323,5.521 0.458,0.198 10 false CANH 5.865,5.844 6.323,6.042 0.458,0.198 10 false CANL 5.656,5.188 6.115,5.385 0.458,0.198 10 false 3 5.667,5.708 6.125,5.906 0.458,0.198 10 false 4 5.281,6.25 5.74,6.448 0.458,0.198 10 false L207 5.719,6.25 7.021,6.729 1.302,0.479 10 false Vehicle Approaching Speaker Controller

C355810E02
0.302,3.365 2.417,3.99 2.115,0.625 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) 0.042,3.365 0.427,3.594 0.385,0.229 10 false L51 2.948,2.438 3.333,2.667 0.385,0.229 10 false L94 2.958,2.969 3.344,3.198 0.385,0.229 10 false L94 2.99,2.25 3.375,2.479 0.385,0.229 10 false 11 2.979,2.781 3.365,3.01 0.385,0.229 10 false 10 0.823,2.427 1.344,2.688 0.521,0.26 10 false CANH 0.844,2.969 1.365,3.229 0.521,0.26 10 false CANL 0.375,1.354 1.969,1.688 1.594,0.333 10 false Airbag ECU Assembly 0.073,1.354 0.458,1.583 0.385,0.229 10 false L16 0.802,0.406 1.323,0.667 0.521,0.26 10 false CANH 0.833,0.958 1.354,1.219 0.521,0.26 10 false CANL 1.333,2.313 1.854,2.573 0.521,0.26 10 false 4 1.323,2.865 1.844,3.125 0.521,0.26 10 false 3 1.313,0.323 1.833,0.583 0.521,0.26 10 false 13 1.333,0.854 1.854,1.115 0.521,0.26 10 false 22 2.948,0.958 3.333,1.188 0.385,0.229 10 false L95 2.958,0.417 3.344,0.646 0.385,0.229 10 false L95 3.031,0.24 3.552,0.5 0.521,0.26 10 false 8 3.021,0.75 3.542,1.01 0.521,0.26 10 false 9 5.573,1.344 7.083,1.938 1.51,0.594 10 false Certification ECU (Smart Key ECU Assembly) 5.219,1.344 5.604,1.573 0.385,0.229 10 false L197 5.615,0.313 6,0.542 0.385,0.229 10 false 14 5.625,0.844 6.01,1.073 0.385,0.229 10 false 15 5.885,0.406 6.406,0.667 0.521,0.26 10 false CANH 5.885,0.948 6.406,1.208 0.521,0.26 10 false CANL 4.063,0.948 4.448,1.177 0.385,0.229 10 false L94 4.063,0.417 4.448,0.646 0.385,0.229 10 false L94 4.135,0.229 4.656,0.49 0.521,0.26 10 false 8 4.146,0.75 4.667,1.01 0.521,0.26 10 false 7 4.083,2.427 4.469,2.656 0.385,0.229 10 false L94 4.063,2.969 4.448,3.198 0.385,0.229 10 false L94 4.156,2.24 4.542,2.469 0.385,0.229 10 false 2 4.135,2.781 4.521,3.01 0.385,0.229 10 false 1 2.75,3.583 4.719,3.917 1.969,0.333 10 false No. 2 CAN Junction Connector 2.854,7.052 4.823,7.385 1.969,0.333 10 false No. 3 CAN Junction Connector 5.552,7.135 5.938,7.365 0.385,0.229 10 false L27 5.833,7.125 7.031,7.604 1.198,0.479 10 false Combination Meter Sub-assembly 6.385,6.479 6.833,6.729 0.448,0.25 10 false 120 Ω 5.646,6.604 6.167,6.865 0.521,0.26 10 false 20 5.875,6.073 6.396,6.333 0.521,0.26 10 false CANH 5.885,6.604 6.406,6.865 0.521,0.26 10 false CANL 5.646,6.073 6.167,6.333 0.521,0.26 10 false 19 4.042,6.188 4.563,6.448 0.521,0.26 10 false L133 4.031,6.719 4.552,6.979 0.521,0.26 10 false L133 4.094,6.531 4.615,6.792 0.521,0.26 10 false 12 4.146,5.979 4.667,6.24 0.521,0.26 10 false 6 2.917,6.188 3.438,6.448 0.521,0.26 10 false L133 2.927,6.719 3.448,6.979 0.521,0.26 10 false L133 3.01,6.542 3.531,6.802 0.521,0.26 10 false 10 3.052,5.99 3.573,6.25 0.521,0.26 10 false 4 0.115,7.104 0.5,7.333 0.385,0.229 10 false L6 0.333,7.104 1.708,7.51 1.375,0.406 10 false Hybrid Vehicle Control ECU 0.865,6.188 1.385,6.448 0.521,0.26 10 false CA1H 0.896,6.719 1.417,6.979 0.521,0.26 10 false CA1L 1.323,6.073 1.844,6.333 0.521,0.26 10 false 25 1.323,6.604 1.844,6.865 0.521,0.26 10 false 24 4.031,4.26 4.552,4.521 0.521,0.26 10 false L133 4.021,4.792 4.542,5.052 0.521,0.26 10 false L133 4.146,4.073 4.667,4.333 0.521,0.26 10 false 5 4.104,4.604 4.625,4.865 0.521,0.26 10 false 11 2.969,4.271 3.49,4.531 0.521,0.26 10 false A68 2.948,4.792 3.469,5.052 0.521,0.26 10 false A68 3.042,4.063 3.563,4.323 0.521,0.26 10 false 1 3.052,4.594 3.573,4.854 0.521,0.26 10 false 7 1.333,4.167 1.854,4.427 0.521,0.26 10 false 16 1.333,4.698 1.854,4.958 0.521,0.26 10 false 15 0.854,4.25 1.375,4.51 0.521,0.26 10 false CA1H 0.875,4.802 1.396,5.063 0.521,0.26 10 false CA1L 0.083,5.188 0.469,5.417 0.385,0.229 10 false A24 0.375,5.188 1.698,5.667 1.323,0.479 10 false Transmission Control ECU Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154783C01
0.75,0.948 0.99,0.948 0.99,0.948 1.552,1.229 false 0.75,1.208 0.99,1.208 0.99,1.208 1.542,1.417 false 0.729,2.219 1.156,2.219 1.156,2.219 1.563,1.833 false 0.75,1.833 1.177,1.833 1.177,1.833 1.573,1.615 false 2.615,2.156 2.104,2.156 2.104,2.156 1.719,1.823 false 2.615,1.865 2.104,1.865 2.104,1.865 1.76,1.635 false 2.656,0.948 2.135,0.948 2.135,0.948 1.74,1.229 false 2.656,1.219 2.427,1.219 2.427,1.219 1.74,1.438 false 1.948,3.01 1.823,3.01 1.823,3.01 1.656,3.49 false 2.615,2.5 2.104,2.5 2.104,2.5 1.719,2.052 false 0.708,2.531 1.135,2.531 1.135,2.531 1.563,2.01 false 0.073,0.094 0.448,0.375 0.375,0.281 10 false *a 0.073,3.01 0.229,3.188 0.156,0.177 10 false *1 2.698,0.865 3.24,1.042 0.542,0.177 10 false CANH*b 2.646,1.771 3.281,2 0.635,0.229 10 false CANH*d 2.646,2.063 3.26,2.292 0.615,0.229 10 false CANH*e 2.698,1.135 3.24,1.313 0.542,0.177 10 false CANH*c 0.104,0.854 0.646,1.031 0.542,0.177 10 false CANL*b 0.104,1.75 0.698,1.969 0.594,0.219 10 false CANL*d 0.104,2.125 0.74,2.354 0.635,0.229 10 false CANL*e 0.104,1.125 0.646,1.302 0.542,0.177 10 false CANL*c 1.594,0.156 2.01,0.354 0.417,0.198 10 false L94 0.229,3.656 0.542,3.833 0.313,0.177 10 false L61 1.99,2.917 2.281,3.094 0.292,0.177 10 false CG 0.177,2.448 0.813,2.677 0.635,0.229 10 false CANL*f 2.667,2.417 3.281,2.646 0.615,0.229 10 false CANH*f
*1 DLC3
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
*c to No. 1 CAN Junction Connector
*d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
*f to Vehicle Approaching Speaker Controller


Disconnect the L94 wire harness connector from the No. 2 CAN junction connector (instrument panel connector holder left side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 3 CAN junction connector
L94-1 (CANL) - L61-4 (CG)
L94-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 CAN junction connector
L94-4 (CANL) - L61-4 (CG)
L94-8 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)
L94-7 (CANL) - L61-4 (CG)
L94-11 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly (steering angle sensor)
L94-10 (CANL) - L61-4 (CG)
L94-14 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Vehicle approaching speaker controller
L94-13 (CANL) - L61-4 (CG)


Result:
Result Proceed to
OK A
NG (Line to No. 1 CAN junction connector) B
NG (Line to No. 3 CAN junction connector) C
NG (Line to ECU or sensor) D




A

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)

B

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.
U191029E02
0.729,0.938 0.969,0.938 0.969,0.938 1.688,1.219 true 0.729,1.208 0.969,1.208 0.969,1.208 1.677,1.417 true 0.708,2.24 1.135,2.24 1.135,2.24 1.698,1.854 true 0.719,1.875 1.146,1.875 1.146,1.875 1.698,1.656 true 2.604,2.198 2.094,2.198 2.094,2.198 1.865,1.865 true 2.594,1.885 2.083,1.885 2.083,1.885 1.885,1.656 true 2.656,0.938 2.135,0.938 2.135,0.938 1.896,1.219 true 2.656,1.208 2.427,1.208 2.427,1.208 1.896,1.427 true 1.927,2.99 1.823,2.99 1.823,2.99 1.646,3.479 true 0.115,0.063 0.458,0.229 0.344,0.167 10 false *a 0.073,2.979 0.229,3.156 0.156,0.177 10 false *1 0.177,0.854 0.719,1.031 0.542,0.177 10 false CANH*b 0.156,1.792 0.698,1.969 0.542,0.177 10 false CANH*d 0.156,2.146 0.698,2.323 0.542,0.177 10 false CANH*e 0.177,1.125 0.719,1.302 0.542,0.177 10 false CANH*c 2.698,0.854 3.24,1.031 0.542,0.177 10 false CANL*b 2.667,1.813 3.208,1.99 0.542,0.177 10 false CANL*d 2.667,2.115 3.208,2.292 0.542,0.177 10 false CANL*e 2.708,1.125 3.25,1.302 0.542,0.177 10 false CANL*c 1.615,0.177 2.031,0.375 0.417,0.198 10 false L95 0.24,3.677 0.552,3.854 0.313,0.177 10 false L61 1.979,2.917 2.25,3.094 0.271,0.177 10 false CG

Disconnect the L95 wire harness connector from the No. 2 CAN junction connector (instrument panel connector holder right side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Power Steering ECU Assembly
*c to Air Conditioning Amplifier Assembly
*d to Airbag ECU Assembly
*e to Central Gateway ECU (Network Gateway ECU)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L95-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
L95-3 (CANL) - L61-4 (CG)
L95-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
L95-6 (CANL) - L61-4 (CG)
L95-8 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag ECU assembly
L95-9 (CANL) - L61-4 (CG)
L95-11 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
L95-12 (CANL) - L61-4 (CG)




OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.
U154826E03
2,1.51 2,0.688 2,0.688 1.802,0.688 false 2.031,1.792 2.031,2.333 2.031,2.333 1.771,2.333 false 2.167,1.51 2.167,0.688 2.167,0.688 2.365,0.688 false 2.198,1.792 2.198,2.344 2.198,2.344 2.458,2.344 false 1.875,2.969 1.802,2.969 1.802,2.969 1.635,3.5 false 0.115,2.677 0.365,2.917 0.25,0.24 10 false *1 0.115,0.052 0.365,0.292 0.25,0.24 10 false *a 1.229,0.594 1.917,0.844 0.688,0.25 10 false CANH*b 1.208,2.24 1.896,2.49 0.688,0.25 10 false CANL*b 2.427,0.594 3.115,0.844 0.688,0.25 10 false CANH*c 2.5,2.26 3.188,2.51 0.688,0.25 10 false CANL*c 1.927,2.875 2.24,3.135 0.313,0.26 10 false CG 0.24,3.75 0.656,4 0.417,0.25 10 false L61 0.354,1.479 0.771,1.729 0.417,0.25 10 false L132

Disconnect the L132 wire harness connector from the No. 1 CAN junction connector (instrument panel wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to No. 2 CAN Junction Connector


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L132-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
L132-11 (CANL) - L61-4 (CG)
L132-6 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 2 CAN junction connector
L132-12 (CANL) - L61-4 (CG)


Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to ECU or sensor) C




A

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.
U154827E02
1.292,1.49 1.292,0.667 1.292,0.667 1.094,0.667 false 1.292,1.792 1.292,2.417 1.292,2.417 1.031,2.417 false 1.469,1.49 1.469,0.667 1.469,0.667 1.667,0.667 false 1.479,1.802 1.479,2.427 1.479,2.427 1.74,2.427 false 1.823,3.042 1.74,3.042 1.74,3.042 1.615,3.542 false 0.094,2.76 0.344,3 0.25,0.24 10 false *1 0.135,0.146 0.385,0.385 0.25,0.24 10 false *a 0.521,0.573 1.208,0.823 0.688,0.25 10 false CANH*b 0.438,2.323 1.125,2.573 0.688,0.25 10 false CANL*b 1.719,0.573 2.406,0.823 0.688,0.25 10 false CANH*c 1.802,2.323 2.49,2.573 0.688,0.25 10 false CANL*c 1.885,2.948 2.156,3.146 0.271,0.198 10 false CG 0.208,3.75 0.625,4 0.417,0.25 10 false L61 0.365,1.479 0.781,1.729 0.417,0.25 10 false A67

Disconnect the A67 wire harness connector from the No. 1 CAN junction connector (engine room main wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A67-7 (CANL) - L61-4 (CG)
A67-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)
A67-8 (CANL) - L61-4 (CG)




OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.
U154828E02
1.833,1.49 1.833,0.667 1.833,0.667 1.635,0.667 false 1.823,1.792 1.823,2.417 1.823,2.417 1.563,2.417 false 2.021,1.49 2.021,0.667 2.021,0.667 2.219,0.667 false 2,1.802 2,2.427 2,2.427 2.26,2.427 false 2.208,1.5 2.583,1.125 2.583,1.125 2.656,1.125 false 2.208,1.76 2.583,2.135 2.583,2.135 2.646,2.135 false 1.865,2.958 1.75,2.958 1.75,2.958 1.646,3.521 false 0.146,2.677 0.396,2.917 0.25,0.24 10 false *1 0.177,0.156 0.448,0.417 0.271,0.26 10 false *a 1.052,0.573 1.74,0.823 0.688,0.25 10 false CANH*b 1.01,2.323 1.698,2.573 0.688,0.25 10 false CANL*b 2.271,0.563 2.958,0.813 0.688,0.25 10 false CANH*c 2.313,2.323 3,2.573 0.688,0.25 10 false CANL*c 1.906,2.854 2.188,3.083 0.281,0.229 10 false CG 0.188,3.74 0.604,3.99 0.417,0.25 10 false L61 0.354,1.479 0.792,1.75 0.438,0.271 10 false L133 2.708,1.031 3.271,1.281 0.563,0.25 10 false CANH*d 2.708,2.031 3.26,2.281 0.552,0.25 10 false CANL*d

Disconnect the L133 wire harness connector from the No. 3 CAN junction connector (instrument panel wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to No. 2 CAN Junction Connector
*d to Combination Meter Sub-assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L133-4 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
L133-10 (CANL) - L61-4 (CG)
L133-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 2 CAN junction connector
L133-11 (CANL) - L61-4 (CG)
L133-6 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Combination meter sub-assembly
L133-12 (CANL) - L61-4 (CG)


Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to ECU or sensor) C




A

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.
U154829E02
1.281,1.479 1.281,0.656 1.281,0.656 1.083,0.656 false 1.292,1.823 1.292,2.448 1.292,2.448 1.031,2.448 false 1.854,3 1.76,3 1.76,3 1.635,3.51 false 0.094,2.677 0.344,2.917 0.25,0.24 10 false *1 0.115,0.135 0.365,0.375 0.25,0.24 10 false *a 0.5,0.552 1.188,0.802 0.688,0.25 10 false CANH*b 0.479,2.354 1.167,2.604 0.688,0.25 10 false CANL*b 1.906,2.906 2.26,3.198 0.354,0.292 10 false CG 0.219,3.74 0.635,3.99 0.417,0.25 10 false L61 0.385,1.479 0.802,1.729 0.417,0.25 10 false A68

Disconnect the A68 wire harness connector from the No. 3 CAN junction connector (engine room main wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Transmission Control ECU Assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A68-7 (CANL) - L61-4 (CG)




OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
7.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).



c.

Measure the resistance according to the value(s) in the table below.

U191200E02
1.948,1.406 1.948,0.688 1.948,0.688 2.281,0.688 false 1.854,1.406 1.854,0.688 1.854,0.688 1.49,0.688 false 5.25,1.177 5.25,0.75 5.25,0.75 5.021,0.75 false 0.135,0.073 0.51,0.354 0.375,0.281 10 false *a 1.073,0.604 1.906,0.917 0.833,0.313 10 false CA4H 2.323,0.604 3.156,0.917 0.833,0.313 10 false CA4L 4.76,0.677 5.594,0.99 0.833,0.313 10 false CG 1.74,0.115 2.271,0.333 0.531,0.219 10 false L192 3.875,0.083 4.25,0.365 0.375,0.281 10 false *1 5.25,0.125 5.781,0.344 0.531,0.219 10 false L61

Text in Illustration
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -

Standard Resistance:
Tester Connection Condition Specified Condition
L192-18 (CA4H) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-17 (CA4L) - L61-4 (CG)



HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR