Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The Combination meter sub-assembly receives a text data signal from the navigation receiver assembly via local bus communication.

Based on this signal, navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter sub-assembly cannot receive the signal.

DTC No. DTC Detection Condition Trouble Area
B150A After the combination meter sub-assembly receives a registration information signal, which is sent by the radio and display receiver assembly when the power switch is turned on (ACC), 1 or more times, the combination meter sub-assembly does not receive the signal for 30 seconds or more.
·

Harness or connector

·

Navigation receiver assembly

·

Combination meter sub-assembly



WIRING DIAGRAM

E309057E05
1.104,1.573 2.396,1.948 1.292,0.375 10 false Navigation Receiver Assembly 4.281,1.594 4.563,1.75 0.281,0.156 10 false L27 4.594,1.594 6.813,1.969 2.219,0.375 10 false Combination Meter Sub-assembly 4.896,0.406 5.198,0.563 0.302,0.156 10 false 29 4.896,0.969 5.198,1.125 0.302,0.156 10 false 28 2.333,0.938 2.635,1.094 0.302,0.156 10 false 3 1.792,0.552 2.25,0.708 0.458,0.156 10 false CNL1 1.771,1.104 2.229,1.26 0.458,0.156 10 false CNH1 5.135,0.552 5.594,0.708 0.458,0.156 10 false MSCL 5.146,1.115 5.604,1.271 0.458,0.156 10 false MSCH 0.802,2.385 3.177,2.583 2.375,0.198 10 false : Local Bus Communication Line 2.75,0.938 3.052,1.094 0.302,0.156 10 false 3 2.333,0.375 2.635,0.531 0.302,0.156 10 false 4 2.75,0.375 3.052,0.531 0.302,0.156 10 false 4 2.292,1.302 2.594,1.458 0.302,0.156 10 false *1 2.708,1.302 3.01,1.458 0.302,0.156 10 false *2 2.292,0.74 2.594,0.896 0.302,0.156 10 false *1 2.698,0.74 3,0.896 0.302,0.156 10 false *2 2.229,0.552 2.646,0.708 0.417,0.156 10 false L172 2.24,1.115 2.656,1.271 0.417,0.156 10 false L172 2.635,0.552 3.052,0.708 0.417,0.156 10 false L173 2.646,1.115 3.063,1.271 0.417,0.156 10 false L173 3.521,2.073 6.458,2.271 2.938,0.198 10 false *1: w/o Intelligent Parking Assist System 3.521,2.375 6.458,2.573 2.938,0.198 10 false *2: w/ Intelligent Parking Assist System

PROCEDURE

1.CHECK FOR DTC
a.

Check if navigation system DTCs are output (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR).

Result:
Result Proceed to
Navigation system DTCs are not output A
Navigation system DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the L172*1 or L173*2 navigation receiver assembly connector.

*1: w/o Intelligent Parking Assist System

*2: w/ Intelligent Parking Assist System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Intelligent Parking Assist System:
Tester Connection Condition Specified Condition
L27-29 (MSCL) - L172-4 (CNL1) Always Below 1 Ω
L27-28 (MSCH) - L172-3 (CNH1) Always Below 1 Ω
L27-29 (MSCL) - Body ground Always 10 kΩ or higher
L27-28 (MSCH) - Body ground Always 10 kΩ or higher

w/ Intelligent Parking Assist System:
Tester Connection Condition Specified Condition
L27-29 (MSCL) - L173-4 (CNL1) Always Below 1 Ω
L27-28 (MSCH) - L173-3 (CNH1) Always Below 1 Ω
L27-29 (MSCL) - Body ground Always 10 kΩ or higher
L27-28 (MSCH) - Body ground Always 10 kΩ or higher




OK

3.REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE COMBINATION METER SUB-ASSEMBLY
a.

Replace the combination meter sub-assembly with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter sub-assembly and navigation receiver assembly.



c.

Operate the steering pad switch RH and check that the audio tab illuminates.


d.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output A
The audio tab does not illuminate and DTC B150A is output B




A

END

B