Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter sub-assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU which uses this information to create the vehicle speed sensor signal*a. The vehicle speed sensor signal consists of pulses sent to the combination meter sub-assembly from the skid control ECU. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter sub-assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter sub-assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter sub-assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter sub-assembly controls its respective system based on the pulse signal.

·

*a: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter sub-assembly operation. Combination meter sub-assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

for LHD
E436060E01
0.688,1.417 1.146,1.615 0.458,0.198 10 false A58 0.677,1.594 2.083,1.99 1.406,0.396 10 false Skid Control ECU 0.063,2.802 0.521,3 0.458,0.198 10 false L197 0.042,2.979 3.021,3.438 2.979,0.458 10 false Certification ECU (Smart Key ECU Assembly) 1.406,0.521 1.865,0.719 0.458,0.198 10 false SP1 5.271,0.531 5.729,0.729 0.458,0.198 10 false 16 1.406,2.417 1.865,2.615 0.458,0.198 10 false SPD 1.802,2.417 2.26,2.615 0.458,0.198 10 false 27 5.563,0.646 6.021,0.844 0.458,0.198 10 false S1 5.281,0.927 5.74,1.125 0.458,0.198 10 false 15 5.552,1.052 6.01,1.25 0.458,0.198 10 false +S 3.531,1.813 3.99,2.01 0.458,0.198 10 false 32 2.854,2.438 3.313,2.635 0.458,0.198 10 false 22 3.927,2.438 4.385,2.635 0.458,0.198 10 false 31 5.292,2.427 5.75,2.625 0.458,0.198 10 false 16 4.958,4.292 5.417,4.49 0.458,0.198 10 false L146 4.99,2.99 7.104,3.583 2.115,0.594 10 false Headlight Leveling ECU Assembly 5.552,2.427 6.01,2.625 0.458,0.198 10 false SPDR 3.917,3.896 4.375,4.094 0.458,0.198 10 false 12 3.052,4.448 4.333,4.854 1.281,0.406 10 false Junction Connector 2.698,4.458 3.156,4.656 0.458,0.198 10 false L70 4.969,4.469 7.156,4.885 2.188,0.417 10 false Windshield Wiper Relay Assembly 1.802,0.521 2.26,0.719 0.458,0.198 10 false 11 5.552,3.896 6.01,4.094 0.458,0.198 10 false SPD 5.271,3.885 5.729,4.083 0.458,0.198 10 false 24 5,2.823 5.458,3.021 0.458,0.198 10 false A48 5.01,1.406 5.375,1.635 0.365,0.229 10 false L27 5,1.573 7.094,1.958 2.094,0.385 10 false Combination Meter Sub-assembly

for RHD
E436061E01
0.646,1.667 2.854,1.844 2.208,0.177 10 false Skid Control ECU 0.656,1.5 2.865,1.677 2.208,0.177 10 false A58 1.396,0.604 3.604,0.781 2.208,0.177 10 false SP1 1.792,0.594 4,0.771 2.208,0.177 10 false 11 5.26,0.594 5.51,0.771 0.25,0.177 10 false 16 5.271,1 5.521,1.177 0.25,0.177 10 false 15 5.563,0.688 6.375,0.875 0.813,0.188 10 false S1 5.573,1.094 6.385,1.281 0.813,0.188 10 false +S 4.99,1.677 7.156,1.969 2.167,0.292 10 false Combination Meter Sub-assembly 5.01,1.5 5.396,1.729 0.385,0.229 10 false L27 3.521,1.917 3.906,2.146 0.385,0.229 10 false 31 2.833,2.5 3.219,2.729 0.385,0.229 10 false 22 3.917,2.51 4.302,2.74 0.385,0.229 10 false 12 5.26,2.5 5.646,2.729 0.385,0.229 10 false 17 5.563,2.5 5.948,2.729 0.385,0.229 10 false SPD 5.063,2.917 5.448,3.146 0.385,0.229 10 false L38 5.063,3.083 7.156,3.5 2.094,0.417 10 false Navigation Receiver Assembly*1 0.146,2.917 2.354,3.094 2.208,0.177 10 false L197 0.115,3.083 3.281,3.5 3.167,0.417 10 false Certification ECU (Smart Key ECU Assembly) 0.323,4.417 2.531,4.594 2.208,0.177 10 false A48 0.323,4.583 2.656,4.948 2.333,0.365 10 false Headlight Leveling ECU Assembly*2 1.375,2.49 1.896,2.719 0.521,0.229 10 false SPD 1.781,2.49 2.302,2.719 0.521,0.229 10 false 27 2.813,3.979 3.333,4.208 0.521,0.229 10 false 32 3.896,3.99 4.417,4.219 0.521,0.229 10 false 11 1.292,3.979 1.813,4.208 0.521,0.229 10 false SPDR 5.563,3.979 6.083,4.208 0.521,0.229 10 false SPD 5.219,4.427 6.354,4.719 1.135,0.292 10 false L31 5.208,4.583 6.948,4.969 1.74,0.385 10 false Stereo Component Amplifier Assembly*1 2.802,4.542 5.01,4.719 2.208,0.177 10 false L70 3.115,4.552 4.417,4.813 1.302,0.26 10 false Junction Connector 0.521,5.333 2.854,5.698 2.333,0.365 10 false *1: w/ Navigation System 3.031,5.333 5.365,5.698 2.333,0.365 10 false *2: for LED Headlight 1.792,3.979 2.313,4.208 0.521,0.229 10 false 16 5.24,3.979 5.552,4.177 0.313,0.198 10 false 11

PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
U155025E02
2.24,2.333 2.938,1.948 false 0.24,0.188 0.438,0.375 0.198,0.188 10 false *a 0.844,1.313 1.177,1.49 0.333,0.177 10 false L27 2.969,1.823 3.167,2 0.198,0.177 10 false +S

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified 0Condition
L27-15 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)

HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter sub-assembly, the combination meter sub-assembly will output a waveform.




OK

2.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)
2.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT VOLTAGE)
a.

Reconnect the L27 combination meter sub-assembly connector.


b.
U154747E01
0.196,0.213 0.380,0.371 0.184,0.158 10 *a 0.265,0.884 0.553,1.041 0.288,0.158 10 A58 2.486,0.898 2.19,1.711 false 2.51,0.826 2.819,0.983 0.309,0.158 10 SP1

Disconnect the A58 skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-11 (SP1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

3.INSPECT SKID CONTROL ECU (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - SKID CONTROL ECU)
3.INSPECT SKID CONTROL ECU (INPUT WAVEFORM)
a.
U190823E03
1.156,1.24 0.958,0.708 false 1.125,3.906 1.375,3.906 false 1.073,3.708 1.073,4.031 false 1.448,3.708 1.448,4.031 false 0.135,0.115 0.292,0.271 0.156,0.156 10 false *a 0.802,0.531 0.99,0.688 0.188,0.156 10 false SI 2.771,3.656 3.094,3.813 0.323,0.156 10 false GND 1.177,3.927 1.385,4.083 0.208,0.156 10 false (A) 1.625,0.469 1.927,0.625 0.302,0.156 10 false L27

Check the input waveform.

i.

Reconnect the A58 skid control ECU connector.


ii.

Remove the combination meter sub-assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal L27-16 (SI) and body ground.


iv.

Turn the power switch on (IG).


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


OK:

The waveform is displayed as shown in the illustration.

Text in Illustration
*a Component with harness connected
(Combination Meter Sub-assembly)


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

C

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - SKID CONTROL ECU)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-11 (SP1) - L27-16 (SI) Always Below 1 Ω
A58-11 (SP1) - Body ground Always 10 kΩ or higher




A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L70 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-15 (+S) - L70-32*1 Always Below 1 Ω
L27-15 (+S) - L70-31*2 Always Below 1 Ω
L27-15 (+S) - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)
a.

Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.


U155087E02
0.094,0 0.719,0.354 0.625,0.354 10 false *a 3.771,2.292 4.125,2.469 0.354,0.177 10 false L70

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for LHD):
Tester Connection Condition Specified Condition
L70-12 - Body ground Power switch on (IG) 4.5 to 14 V
L70-22 - Body ground Power switch on (IG) 4.5 to 14 V
L70-31 - Body ground Power switch on (IG) 4.5 to 14 V


Standard Voltage (for RHD):
Tester Connection Condition Specified Condition
L70-11 - Body ground*1 Power switch on (IG) 4.5 to 14 V
L70-12 - Body ground*1 Power switch on (IG) 4.5 to 14 V
L70-22 - Body ground Power switch on (IG) 4.5 to 14 V
L70-32 - Body ground*2 Power switch on (IG) 4.5 to 14 V


*1: w/ Navigation system

*2: w/ LED headlight


Text in Illustration
*a Front view of wire harness connector
(to Junction Connector)

Result:
Result Proceed to
Voltage is not present in one circuit (for LHD) A
Voltage is present in all the circuits (for RHD) B
Voltage is present in all the circuits C





A

7.SYSTEM CHECK

B

8.SYSTEM CHECK

C

REPAIR OR REPLACE INSTRUMENT PANEL WIRE (JUNCTION CONNECTOR)

7.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in step 6.

Result:
Tester Connection System that Uses the Circuit Proceed to
L70-12 - Body ground Wiper and Washer System A
L70-22 - Body ground Entry and Start System B
L70-31 - Body ground Lighting System C




A

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY CIRCUIT)

B

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY CIRCUIT)

C

13.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY CIRCUIT)
8.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in step 6.

Result:
Tester Connection System that Uses the Circuit Proceed to
L70-11 - Body ground*1 Navigation System A
L70-12 - Body ground*1 Navigation System B
L70-22 - Body ground Entry and Start System C
L70-32 - Body ground*2 Lighting System D


*1: w/ Navigation system

*2: for LED headlight




A

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY CIRCUIT)

B

11.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY CIRCUIT)

C

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY CIRCUIT)

D

13.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY CIRCUIT)
9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY CIRCUIT)
a.

Disconnect the L31 stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L31-11 (SPD) - Body ground Always 10 kΩ or higher




OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY CIRCUIT)
a.

Disconnect the L146 windshield wiper relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L146-24 (SPD) - Body ground Always 10 kΩ or higher




OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY CIRCUIT)
a.

Disconnect the L38 navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-17 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY CIRCUIT)
a.

Disconnect the L197 Certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L197-27 (SPD) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY CIRCUIT)
a.

Disconnect the A48 headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-16 (SPDR) - Body ground Always 10 kΩ or higher




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR