Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Oil Pressure Switch Circuit  


DESCRIPTION

The combination meter sub-assembly and engine oil pressure switch assembly are connected via direct line. The combination meter sub-assembly determines the engine oil pressure based on the engine oil pressure switch status signal.

HINT:
·

The combination meter sub-assembly receives various vehicle information signals from the hybrid vehicle control ECU via CAN communication in order to output warnings.

·

The combination meter sub-assembly operates the following to output oil pressure warnings:

(a)

Engine oil pressure warning buzzer

(b)

Engine oil pressure warning message on multi-information display




WIRING DIAGRAM

E414068E23
0.875,1.156 2.917,1.406 2.042,0.25 10 false Hybrid Vehicle Control ECU 0.635,2.875 3.219,3.24 2.583,0.365 10 false Engine Oil Pressure Switch Assembly 0.635,2.698 1.094,2.896 0.458,0.198 10 false D26 4.833,2.875 5.146,3.073 0.313,0.198 10 false L27 4.823,3.042 6.917,3.531 2.094,0.49 10 false Combination Meter Sub-assembly 4.948,2.083 5.563,2.281 0.615,0.198 10 false S 4.729,2.083 5.042,2.281 0.313,0.198 10 false 7 5.635,1.729 6.25,1.927 0.615,0.198 10 false 12 V 2.396,2.083 2.708,2.281 0.313,0.198 10 false 1 0.552,3.417 2.792,3.656 2.24,0.24 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

The following troubleshooting procedure is based on the assumption that the hybrid control system is normal. Confirm that the hybrid control system is not malfunctioning before performing the following procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Pressure Switch Engine oil pressure switch / OFF or ON OFF: Engine started -
ON: Engine not started


Result:
Result Proceed to
The Data List item changes correctly A
The Data List item do not change correctly B



A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

2.INSPECT ENGINE OIL PRESSURE SWITCH ASSEMBLY
2.INSPECT ENGINE OIL PRESSURE SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)

NG

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the D26 engine oil pressure switch assembly connector.


b.

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D26-1 - L27-7 (S) Always Below 1 Ω
D26-1 or L27-7 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR