Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2020.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C156569E02
0.25,0.213 0.489,0.390 0.239,0.177 10 *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU)
- -

Terminal No. (Symbol) Terminal Description
1 (MRI1) Motor power supply input 1
2 (MRI2) Motor power supply input 2
3 (STPO) Stop light control relay output
4 - (Not used)
5 (FR-) Front speed sensor RH (-) signal input
6 (STP2) Stop light control relay input
7 (RL-) Rear speed sensor LH (-) signal input
8 - (Not used)
9 (RR-) Rear speed sensor RH (-) signal input
10 - (Not used)
11 (SP1) Speed sensor signal output
12 (IG2) IG2 power source input
13 - (Not used)
14 (BI) +B power source input
15 (BS) Solenoid power supply input
16 (IG1) IG1 power source input
17 - (Not used)
18 (FR+) Front speed sensor RH (+) power supply output
19 (CTY) Courtesy switch input
20 (RL+) Rear speed sensor LH (+) power supply output
21 - (Not used)
22 (RR+) Rear speed sensor RH (+) power supply output
23 (GND6) Skid control ECU ground 6
24 (GND5) Skid control ECU ground 5
25 (GND4) Skid control ECU ground 4
26 (GND3) Skid control ECU ground 3
27 (GND2) Skid control ECU ground 2
28 (GND) Skid control ECU ground
29 (MRO1) Motor power supply output 1
30 (MRO2) Motor power supply output 2
31 (FL+) Front speed sensor LH (+) power supply output
32 (FL-) Front speed sensor LH (-) signal input
33 (STP) Stop light switch input
34 (CA2L) CAN communication line 2 (L)
35 (CA2H) CAN communication line 2 (H)
36 (LBL) Brake fluid level warning switch input
37 (CA1H) CAN communication line 1 (H)
38 (CA1L) CAN communication line 1 (L)
39 (VCSK) Stroke sensor power supply output
40 (SKS2) Stroke sensor signal input 2
41 (SKG) Stroke sensor ground
42 (SKS) Stroke sensor signal input


TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

U154694E03
0.323,0.229 0.5,0.385 0.177,0.156 10 false *a 1.573,1.542 1.844,1.688 0.271,0.146 10 false A58

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)
- -

HINT:

Voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-1 (MRI1) - Body ground B - Body ground Motor power supply input 1 Always 11 to 14 V
A58-2 (MRI2) - Body ground R - Body ground Motor power supply input 2 Always 11 to 14 V
A58-3 (STPO) - Body ground*1 Y - Body ground Stop light control relay output Always 11 to 14 V
A58-6 (STP2) - Body ground*1 L - Body ground Stop light control relay input Stop light switch ON → OFF
(Brake pedal depressed → released)
11 to 14 V → Below 1.5 V
A58-12 (IG2) - Body ground BE - Body ground IG2 power source input Power switch on (IG) 11 to 14 V
A58-14 (BI) - Body ground W - Body ground +B power source input Always 11 to 14 V
A58-15 (BS) - Body ground B - Body ground Solenoid power supply input Always 11 to 14 V
A58-16 (IG1) - Body ground B - Body ground IG1 power source input Power switch on (IG) 11 to 14 V
A58-19 (CTY) - Body ground V - Body ground Courtesy switch input Driver door close → open 11 to 14 V → Below 1.5 V
A58-23 (GND6) - Body ground W-B - Body ground Skid control ECU ground 6 Always Below 1 Ω
A58-24 (GND5) - Body ground W-B - Body ground Skid control ECU ground 5 Always Below 1 Ω
A58-25 (GND4) - Body ground W-B - Body ground Skid control ECU ground 4 Always Below 1 Ω
A58-26 (GND3) - Body ground W-B - Body ground Skid control ECU ground 3 Always Below 1 Ω
A58-27 (GND2) - Body ground W-B - Body ground Skid control ECU ground 2 Always Below 1 Ω
A58-28 (GND) - Body ground W - Body ground Skid control ECU ground Always Below 1 Ω
A58-33 (STP) - Body ground L - Body ground Stop light switch input Stop light switch ON → OFF
(Brake pedal depressed → released)
11 to 14 V → Below 1.5 V
A58-36 (LBL) - Body ground P - Body ground Brake fluid level warning switch input Brake fluid level warning switch OFF → ON 1.84 to 2.16 kΩ → Below 1 Ω

*1: w/ Dynamic Radar Cruise Control