Home › Steering › STEERING COLUMN › STEERING PAD SWITCH › from 2020.08
RM2070E _55 Steering _061929 STEERING COLUMN _0301717 STEERING PAD SWITCH G

STEERING COLUMN  STEERING PAD SWITCH  INSPECTION  


PROCEDURE

Hide 84247A 1.INSPECT STEERING PAD SWITCH LH

a.

Measure the resistance according to the value(s) in the table below.

E256142E02
0.147,0.117 0.502,0.283 0.355,0.166 10 *a 1.051,0.793 1.406,0.959 0.355,0.166 10 *b 1.021,1.865 1.376,2.031 0.355,0.166 10 *c 1.135,2.132 1.404,2.299 0.269,0.166 10 *g 1.229,2.455 1.583,2.621 0.355,0.166 10 *h 1.428,2.818 1.783,2.985 0.355,0.166 10 *i 0.959,1.191 1.314,1.357 0.355,0.166 10 *d 2.163,0.471 2.517,0.637 0.355,0.166 10 *e 2.258,1.914 2.613,2.081 0.355,0.166 10 *f 4.601,2.437 4.956,2.603 0.355,0.166 10 EAU 3.924,2.432 4.278,2.598 0.355,0.166 10 AU2 3.46,2.426 3.815,2.593 0.355,0.166 10 AU1 1.471,1.254 1.158,0.942 false 1.471,1.579 1.158,1.891 false 1.565,1.362 1.111,1.272 false 1.79,1.242 2.211,0.603 false 1.798,1.585 2.255,1.913 false 1.774,2.029 1.296,2.194 false 1.874,2.286 1.384,2.533 false 1.966,2.507 1.539,2.838 false 3.899,2.071 3.563,2.407 false 4.068,2.071 4.068,2.407 false 4.391,2.074 4.727,2.41 false

Standard Resistance:
Tester Connection Condition Specified Condition
4 (AU1) - 1 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
3 (AU2) - 1 (EAU) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 323 to 335 Ω
Off hook switch pushed 980 to 1020 Ω
Voice switch pushed 3048 to 3172 Ω


HINT:

If the result is not as specified, replace the steering pad switch LH.


Text in Illustration
*a Component without harness connected
(Steering Pad Switch LH)
*b Volume+
*c Volume- *d MODE
*e Seek+ *f Seek-
*g Voice *h On hook
*i Off hook - -


b.

Check the illumination.

E256143E02
3.642,1.481 3.997,1.647 0.355,0.166 10 EAU 3.548,2.305 3.902,2.471 0.355,0.166 10 IL+2 4.042,1.982 3.758,2.287 false 4.16,1.982 3.815,1.637 false 0.196,0.122 0.551,0.288 0.355,0.166 10 *a

i.

Connect an auxiliary battery positive (+) lead to terminal 2 (IL+2) and a negative (-) lead to terminal 1 (EAU) of the steering pad switch LH connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


HINT:

If the result is not as specified, replace the steering pad switch LH.


Text in Illustration
*a Component without harness connected
(Steering Pad Switch LH)
- -



Hide 84244B 2.INSPECT STEERING PAD SWITCH RH

a.

Measure the resistance according to the value(s) in the table below.

U155196E03
2.01,1.333 2.135,0.844 false 2.125,1.75 1.875,1.385 false 1.729,2.083 1.729,1.396 false 1.229,1.74 1.594,1.385 false 6.042,2.552 5.323,2.448 false 6.073,2.25 5.417,2.219 false 6.156,1.969 5.521,1.958 false 6.344,1.198 5.854,1.365 false 6.25,1.531 5.646,1.583 false 4.927,1.729 5.417,1.365 false 5.646,1.156 5.969,0.646 false 5.656,1.375 6.198,0.896 false 3.125,3 3.479,2.656 false 3.531,3.052 3.594,2.656 false 3.99,3.125 3.698,2.667 false 4.052,2.823 3.813,2.646 3.813,2.646 3.844,2.656 false 3.042,2.813 3.354,2.646 false 2.906,2.531 3.365,2.51 false 3.021,2.229 3.469,2.479 false 3.927,1.76 3.573,2.479 false 4.042,1.927 3.677,2.49 false 4.073,2.125 3.802,2.49 false 2.813,1.99 2.354,2.063 false 0.188,0.063 0.906,0.271 0.719,0.208 10 false *a 2.135,0.688 2.854,0.896 0.719,0.208 10 false AU1 2.156,1.74 2.875,1.948 0.719,0.208 10 false AU2 1.604,2.094 2.323,2.302 0.719,0.208 10 false IL+2 0.99,1.75 1.708,1.958 0.719,0.208 10 false EAU 0.938,1.271 1.354,1.479 0.417,0.208 10 false SR2 6.01,0.552 6.729,0.76 0.719,0.208 10 false *b 6.198,0.792 6.917,1 0.719,0.208 10 false *f 6.344,1.115 7.063,1.323 0.719,0.208 10 false *e 6.313,1.448 7.031,1.656 0.719,0.208 10 false *c 6.208,1.854 6.927,2.063 0.719,0.208 10 false *g 6.125,2.198 6.844,2.406 0.719,0.208 10 false *h 6.188,2.49 6.698,2.698 0.51,0.208 10 false *A 6.063,2.469 6.292,2.677 0.229,0.208 10 false *i 4.75,1.688 4.979,1.896 0.229,0.208 10 false *d 3.969,1.646 4.479,1.854 0.51,0.208 10 false +DP2 4.063,1.844 4.573,2.052 0.51,0.208 10 false DIST*A 4.104,2.031 4.615,2.24 0.51,0.208 10 false IL+2 4.073,2.813 4.573,3.021 0.5,0.208 10 false AU1 3.896,3.115 4.25,3.323 0.354,0.208 10 false AU2 3.406,3.073 3.771,3.281 0.365,0.208 10 false EAU 2.875,3.031 3.313,3.24 0.438,0.208 10 false +DP 2.552,2.76 3.083,2.969 0.531,0.208 10 false ECC*A 2.646,2.458 2.948,2.667 0.302,0.208 10 false HO 2.688,2.167 3.125,2.375 0.438,0.208 10 false TRIP 4.177,2.438 4.677,2.646 0.5,0.208 10 false z9 2.219,1.99 2.469,2.198 0.25,0.208 10 false *j

Standard Resistance:
Tester Connection Condition Specified Condition
z9-1 (HO) - Terminal-A Always Below 1 Ω
z9-2 (TRIP) - z9-8 (EAU) No switch pushed 1 MΩ or higher
TRIP switch pushed Below 2.5 Ω
z9-3 (+DP2) - z9-8 (EAU) No switch pushed 95 to 105 kΩ
Left switch pushed Below 2.5 Ω
Up switch pushed 323 to 335 Ω
Down switch pushed 980 to 1020 Ω
Right switch pushed 3048 to 3172 Ω
z9-4 (DIST) - z9-6 (ECC)* No switch pushed 1 MΩ or higher
Distance control switch pushed Below 2.5 Ω
z9-7 (+DP) - z9-8 (EAU) No switch pushed 1 MΩ or higher
Enter switch pushed Below 2.5 Ω
Back switch pushed 980 to 1020 Ω
SR2-2 (IL+2) - z9-5 (IL+2) Always Below 1 Ω
SR2-4 (AU1) - z9-10 (AU1) Always Below 1 Ω
SR2-3 (AU2) - z9-9 (AU2) Always Below 1 Ω
SR2-1 (EAU) - z9-8 (EAU) Always Below 1 Ω


*: w/ Distance Control Switch


HINT:

If the result is not as specified, replace the steering pad switch RH.


Text in Illustration
*A w/ Distance Control Switch - -
*a Component without harness connected
(Steering Pad Switch RH)
*b Up
*c Down *d Left
*e Right *f Enter
*g Back *h TRIP
*i Distance control *j Terminal-A


b.

Check the illumination.

E306950E03
3.573,2.625 3.125,3.052 3.125,3.052 3.563,2.635 false 4.229,2.083 3.781,2.51 false 4.292,1.979 4.75,2.229 0.458,0.25 10 false IL+2 2.938,3.063 3.302,3.313 0.365,0.25 10 false EAU 0.167,0.125 0.531,0.375 0.365,0.25 10 false *a

i.

Connect an auxiliary battery positive (+) lead to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch RH connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


HINT:

If the result is not as specified, replace the steering pad switch RH.


Text in Illustration
*a Component without harness connected
(Steering Pad Switch RH)
- -