Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2020.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) D

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  OPERATION CHECK  


OPERATION DESCRIPTION


a.

Push-button start function:

i.

When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is depressed, the hybrid control system is started by pressing the power switch.


ii.

When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is not depressed, the power source mode is changed by pressing the power switch. The power source mode changes in the following order every time the power switch is pressed: off → on (ACC) → on (IG) → off.


iii.
B361489E01
0.177,0.167 0.49,0.365 0.313,0.198 10 false *a

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed while not depressing the brake pedal, the power source mode changes to on (ACC) and "POWER ON" in the combination meter assembly.

Text in Illustration
*a "POWER ON" Display


iv.
B361489E01
0.177,0.167 0.49,0.365 0.313,0.198 10 false *a

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed 2 times without depressing the brake pedal, the power source mode changes to on (IG) and "POWER ON" in the combination meter assembly.

Text in Illustration
*a "POWER ON" Display


v.

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the brake pedal is depressed while park (P) has been selected the smart warning light is displayed.


vi.
B592796E01
0.156,0.135 0.469,0.333 0.313,0.198 10 false *a

The hybrid control system starts if the power switch is pressed when the smart warning light is displayed.

Text in Illustration
*a Smart Warning Light Displayed



b.

Changing the power source mode when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:

i.

Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.


ii.

While depressing the brake pedal and facing the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the electrical key transmitter sub-assembly near the power switch.


iii.
B361489E01
0.177,0.167 0.49,0.365 0.313,0.198 10 false *a

A buzzer in the combination meter assembly will sound and the power source mode changes to on (IG) and "POWER ON" is displayed. Pressing the power switch without depressing the brake pedal turns the power source mode from on (IG) to off.

Text in Illustration
*a "POWER ON" Display



c.

Starting the hybrid control system when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:

i.

Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.


ii.

While depressing the brake pedal with park (P) selected and facing the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the electrical key transmitter sub-assembly near the power switch.


iii.

A buzzer in the combination meter assembly sounds, the power source mode changes to on (IG).


iv.

Press the power switch with the brake pedal depressed to start the hybrid control system.




CHECK PUSH-BUTTON START FUNCTION


a.

Check the push-button start function:

i.
B592796E01
0.156,0.135 0.469,0.333 0.313,0.198 10 false *a

Get into the vehicle while carrying the key. With the power switch off and the shift lever in P or N, check that the smart warning light is displayed when the brake pedal is depressed. Check that the hybrid control system starts when the power switch is pressed with the smart warning light is displayed.

Text in Illustration
*a Smart Warning Light Displayed


ii.

While the brake pedal is released and the electrical key transmitter sub-assembly is being carried, check that the power source mode changes in the following order when the power switch is pressed: off → on (ACC) → on (IG) → off.


iii.
B382221E02
3.049,0.104 3.295,0.412 0.246,0.309 10 *a 3.026,0.201 2.393,0.201 2.393,0.201 0.622,0.943 false 2.393,0.201 1.855,0.943 false

Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior key detection area, the electrical key transmitter sub-assembly may not be properly detected if the electrical key transmitter sub-assembly is on the instrument panel, in the glove box or on the floor.


Text in Illustration
*a Inspection Point

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.

·

Perform this inspection for both inspection points.




iv.
B382222E02
1.207,1.342 2.25,0.222 2.25,0.222 1.667,1.042 false 2.288,0.052 2.550,0.257 0.262,0.205 12 *a

Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction as shown in the illustration, and then check that the hybrid control system can be started.

Text in Illustration
*a Inspection Point

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior key detection area, the electrical key transmitter sub-assembly may not be properly detected if the electrical key transmitter sub-assembly is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the rear seat.

·

Perform this inspection for both inspection points.






CHECK TRANSMITTER BATTERY SAVING FUNCTION


a.

Check the transmitter battery saving function:

i.

Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock button and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.


ii.

Check that the smart key system (for Start Function) does not operate while in transmitter battery saving mode.

HINT:

To cancel transmitter battery saving mode, press a button of the electrical key transmitter sub-assembly.





CHECK POWER SOURCE MODE CHANGING FUNCTION


a.

Check the power switch.

i.

Check that the power source mode changes according to the chart below.

Shift Position Brake Pedal Power Source Mode when power switch Pressed
Park (P) selected Released Off → on (ACC) → on (IG) → off
Park (P) selected Released On (READY) → off
Park (P) selected Released On (ACC)* → on (IG)
Park (P) selected Depressed Off → on (READY)
Park (P) selected Depressed On (ACC) → on (READY)
Park (P) selected Depressed On (IG) → on (READY)
Park (P) selected Depressed On (READY) → off
Park (P) selected Depressed On (ACC)* → on (READY)
Park (P) not selected Released or Depressed On (ACC) → on (IG)
Park (P) not selected Released or Depressed On (READY) → off
Park (P) not selected Released or Depressed On (IG) → off

HINT:

*: This situation is only applicable when the power source mode has changed from on (IG) to on (ACC). (Excluding an emergency stop by pressing the power switch 3 times quickly or pressing and holding the power switch for 2 seconds or more.)






CHECK POWER SOURCE MODE INDICATION


a.
B449875E02
0.207,0.14 0.439,0.310 0.232,0.170 10 *a 0.207,1.996 0.439,2.166 0.232,0.170 10 *b

Check the smart warning.

Text in Illustration
*a "POWER ON" Display
*b Smart Warning Light Display

Multi-information Display Inspection
Power Source Mode Multi-information Display
Off
(Excluding conditions in which the hybrid control system can be started)
Off
On (ACC)
(Excluding conditions in which the hybrid control system can be started)
"POWER ON" displayed
On (IG)
(Excluding conditions in which the hybrid control system can be started)
"POWER ON" displayed
Conditions in which hybrid control system can be started*1 Key Warning Light displayed
Hybrid control system started Off

HINT:

*1: Indicates the conditions in which the hybrid control system can be started by pressing the power switch while either of the following conditions is met:

·

Condition 1

All of the following conditions are met:

-

The power source mode was turned from on (IG) to on (ACC).

-

Key verification is OK*2 or immobiliser is unset (power switch is on (ACC) or on (IG)).

-

The stop light switch is on.



·

Condition 2

All of the following conditions are met:

-

The power source mode was not turned from on (IG) to on (ACC).

-

Key verification is OK*2 or immobiliser is unset (power switch is on (ACC) or on (IG)).

-

The stop light switch is on.



*2: When the electrical key transmitter sub-assembly is in the cabin, the ID code sent as a result from communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) and the ID code calculated by the certification ECU (smart key ECU assembly) are compared. If the ID codes match each other, the vehicle recognizes that the electrical key transmitter sub-assembly is in the cabin.