Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301757 POWER DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB and L190 main body ECU (multiplex network body ECU) connectors.

U190882C02
0.708,2.771 1.031,2.771 true 3.156,7.583 3.448,7.75 0.292,0.167 10 false MB 4.875,6.385 5.167,6.552 0.292,0.167 10 false 2A 1.885,6.385 2.177,6.552 0.292,0.167 10 false 2B 1.177,5.115 1.469,5.281 0.292,0.167 10 false 2D 0.51,1.5 0.802,1.667 0.292,0.167 10 false 2D 3.917,5.135 4.208,5.302 0.292,0.167 10 false 2C 0.51,2.177 0.802,2.344 0.292,0.167 10 false 2C 4.792,3.802 5.302,3.969 0.51,0.167 10 false L201 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.583,5.104 5.875,5.271 0.292,0.167 10 false 2E 5.885,5.104 6.094,5.271 0.208,0.167 10 false *A 6.542,5.104 6.75,5.271 0.208,0.167 10 false *B 2.344,3.802 2.792,3.969 0.448,0.167 10 false L190 0.26,2.563 0.552,2.729 0.292,0.167 10 false 2E 0.573,2.552 0.865,2.719 0.292,0.167 10 false *A 0.583,2.854 0.875,3.021 0.292,0.167 10 false *B 0.281,2.854 0.573,3.021 0.292,0.167 10 false 2F 1.938,1.708 2.406,1.875 0.469,0.167 10 false L201 1.938,2.063 2.385,2.229 0.448,0.167 10 false L190 6.271,1.531 6.479,1.698 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.281,2.177 6.49,2.344 0.208,0.167 10 false 2A
*A for LHD *B for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
L190-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-32 (IG) - Body ground - Power switch power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch off Below 1 V


c.

Reconnect the MB and L190 main body ECU (multiplex network body ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2B-1 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2B-1 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder unlocked 11 to 14 V
2B-3 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2B-3 (ACT-) - Body ground LG - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder unlocked 11 to 14 V
2D-11 (ACT-) - Body ground V - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2D-11 (ACT-) - Body ground V - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder unlocked 11 to 14 V
2B-8 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2B-8 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder locked 11 to 14 V
2B-9 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2B-9 (ACT+) - Body ground R - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder locked 11 to 14 V
2B-10 (ACT+) - Body ground P - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2B-10 (ACT+) - Body ground P - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder locked 11 to 14 V
2D-12 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2D-12 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder locked 11 to 14 V
2D-36 (FRCY) - Body ground BR - Body ground*1
V - Body ground*2
Front door courtesy light switch RH input Front door RH open Below 1 V
2D-36 (FRCY) - Body ground BR - Body ground*1
V - Body ground*2
Front door courtesy light switch RH input Front door RH closed 11 to 14 V
2D-35 (FLCY) - Body ground Y - Body ground*1
V - Body ground*2
Front door courtesy light switch LH input Front door LH open Below 1 V
2D-35 (FLCY) - Body ground Y - Body ground*1
V - Body ground*2
Front door courtesy light switch LH input Front door LH closed 11 to 14 V
L201-6 (LRCY) - Body ground G - Body ground Rear door courtesy light switch input Rear door LH or RH open Below 1 V
L201-6 (LRCY) - Body ground G - Body ground Rear door courtesy light switch input Rear door LH and RH closed Pulse generation
L201-11 (L2) - Body ground G - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
L201-11 (L2) - Body ground G - Body ground Driver door key-linked lock input Driver door key cylinder off Pulse generation
L201-12 (UL2) - Body ground V - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
L201-12 (UL2) - Body ground V - Body ground Driver door key-linked unlock input Driver door key cylinder off Pulse generation
L201-7 (LSFL) - Body ground GR - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V
L201-7 (LSFL) - Body ground GR - Body ground Front door LH unlock detection switch input Power switch off, all doors closed and front door LH locked Pulse generation
L201-18 (LSFR) - Body ground LG - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V
L201-18 (LSFR) - Body ground LG - Body ground Front door RH unlock detection switch input Power switch off, all doors closed and front door RH locked Pulse generation
2B-29 (LSR) - Body ground GR - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V
2B-29 (LSR) - Body ground GR - Body ground Rear door RH unlock detection switch input Power switch off, all doors closed, rear door RH and LH locked Pulse generation
2D-25 (LSR) - Body ground GR - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V
2D-25 (LSR) - Body ground GR - Body ground Rear door LH unlock detection switch input Power switch off, all doors closed, rear door LH and RH locked Pulse generation
L201-19 (BCTY) - Body ground L - Body ground Back door courtesy light switch input Back door open Below 1 V
L201-19 (BCTY) - Body ground L - Body ground Back door courtesy light switch input Back door closed and luggage compartment light switch on 11 to 14 V
Back door closed and luggage compartment light switch off Pulse generation

*1: for LHD

*2: for RHD




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry System Back Door Open Function)


U190970E02
1.865,0.563 2.25,0.802 0.385,0.24 10 false L195 3.271,0.542 3.677,0.771 0.406,0.229 10 false L196 4.833,0.542 5.24,0.719 0.406,0.177 10 false L197

a.

Disconnect the L196 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L196-27 (TSW5) - Body ground GR - Body ground Back door opener switch signal Back door opener switch on Below 1 Ω
L196-27 (TSW5) - Body ground GR - Body ground Back door opener switch signal Back door opener switch off 10 kΩ or higher


c.

Reconnect the L196 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L196-27 (TSW5) - Body ground GR - Body ground Back door opener switch signal Back door opener switch off Pulse generation
L196-27 (TSW5) - Body ground GR - Body ground Back door opener switch signal Back door opener switch on Below 1 V



CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)


a.

Disconnect the L206 double lock door control relay assembly connector.

B417822N19
3.354,0.167 3.792,0.385 0.438,0.219 3.396,0.188 3.854,0.385 0.458,0.198 10 false L206


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L206-12 (+B) - Body ground R - Body ground Auxiliary battery power supply Always 11 to 14 V
L206-11 (CPUB) - Body ground L - Body ground Auxiliary battery power supply Always 11 to 14 V
L206-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the L206 double lock door control relay assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L206-6 (DLPD) - Body ground Y - Body ground Front RH double lock position switch input Double lock unset Pulse generation
L206-6 (DLPD) - Body ground Y - Body ground Front RH double lock position switch input Double lock set Below 1 V
L206-5 (DLPP) - Body ground L - Body ground Front LH double lock position switch input Double lock unset Pulse generation
L206-5 (DLPP) - Body ground L - Body ground Front LH double lock position switch input Double lock set Below 1 V
L206-4 (DLPR) - Body ground G - Body ground Rear RH double lock position switch input Double lock unset Pulse generation
L206-4 (DLPR) - Body ground G - Body ground Rear RH double lock position switch input Double lock set Below 1 V
L206-3 (DLPL) - Body ground GR - Body ground Rear LH double lock position switch input Double lock unset Pulse generation
L206-3 (DLPL) - Body ground GR - Body ground Rear LH double lock position switch input Double lock set Below 1 V
L206-8 (ACTS) - Body ground LG - Body ground All door double lock motor set on output Double lock unset Below 1 V
L206-8 (ACTS) - Body ground LG - Body ground All door double lock motor set on output Double lock set 11 to 14 V
L206-1 (ACTR) - Body ground R - Body ground All door double lock motor set off output Double lock set Below 1 V
L206-1 (ACTR) - Body ground R - Body ground All door double lock motor set off output Double lock unset 11 to 14 V