The occupant detection sensor (separate type front seat cushion pad) detects if the passenger seat is occupied and sends signals to the combination meter sub-assembly. The front seat inner belt assembly (for Front Passenger) detects the passenger seat belt condition and sends signals to the combination meter sub-assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad) and front seat inner belt assembly (for Front Passenger), the seat belt warning light in the combination meter sub-assembly will blink or go off.
The seat belt warning light on the combination meter sub-assembly is used for both the driver seat and front passenger seat.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P-Seatbelt Buckle SW | Front passenger seat belt buckle switch signal/ON or OFF | ON: Front passenger seat belt unfastened
OFF: Front passenger seat belt fastened |
- |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the tester screen according to the front passenger seat belt condition | A |
| ON or OFF appears on the tester screen according to the front passenger seat belt condition | B |
A
B
Disconnect the L27 combination meter sub-assembly connector.
Disconnect the S23*1 or R33*2 front seat inner belt assembly (for Front Passenger) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-29 (SW) - S23-3 (+) | Always | Below 1 Ω |
| L27-29 (SW) - Body ground | Always | 10 kΩ or higher |
| S23-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-29 (SW) - R33-3 (+) | Always | Below 1 Ω |
| L27-29 (SW) - Body ground | Always | 10 kΩ or higher |
| R33-2 (E) - Body ground | Always | Below 1 Ω |
OK
NG
| *a | Component without harness connected
(Occupant Detection Sensor (Separate Type Front Seat Cushion Pad)) |
Remove the occupant detection sensor (separate type front seat cushion pad) (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 3 | Front passenger seat occupied | Below 100 Ω |
| 1 - 3 | Front passenger seat not occupied | 1 MΩ or higher |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(Front Seat Inner Belt Assembly (for Front Passenger)) |
Remove the front seat inner belt assembly (for Front Passenger) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S23-3 - B-1 | Always | Below 1 Ω |
| S23-2 - B-3 | Front passenger seat belt unfastened | Below 1 Ω |
| S23-2 - B-3 | Front passenger seat belt fastened | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R33-3 - B-1 | Always | Below 1 Ω |
| R33-2 - B-3 | Front passenger seat belt unfastened | Below 1 Ω |
| R33-2 - B-3 | Front passenger seat belt fastened | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG