OUTLINE OF THEFT DETERRENT SYSTEM
The theft deterrent system can be set by locking the doors using the transmitter or entry and start system.
The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood or back door while the system is in the armed state.
In the alarm sounding state, the hazard warning lights blink. At the same time, the system sounds the vehicle horns or security horn to deter break-in and theft as well as to warn people around the vehicle.
The alarm can be cancelled by unlocking the doors using the transmitter, entry and start system or key*.
*: This function is set through the customize function (See pageVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>CUSTOMIZE PARAMETERS).
Disarmed state:
The alarm function is not operating.
The theft deterrent system is not operating.
Arming preparation state:
The time until the system goes into the armed state.
The theft deterrent system is not operating.
Armed state:
The theft deterrent system is operating.
Alarm sounding state:
The alarm function is operating.
Approx. 27.5 seconds
| Alarm Method | Hazard Warning Lights | Blinking |
| Vehicle Horns | Sounding
(approx. 0.4 second cycles) |
|
| Security Horn | Sounding
(approx. 0.4 second cycles) |
|
| Alarm Time | Approx. 27.5 seconds | |
FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
| Security indicator light | Informs driver of theft deterrent system status. |
| Security horn | Sounds when attempted break-in or theft is detected. |
| Hazard warning lights | Blink when attempted break-in or theft is detected. |
| Vehicle horns | Sound when attempted break-in or theft is detected. |
| Door courtesy light switch | Detects door status (open or closed). |
| Door unlock detection switch | Detects door status (locked or unlocked). |
| Engine hood courtesy switch | Detects engine hood status (open or closed). |
| Back door courtesy switch | Detects back door status (open or closed). |
ACTIVE ARMING MODE
Active arming mode starts the alarm control immediately after the doors are locked.
Active arming mode:
This system operates as described in the diagram below when one of the items for each condition is met.
| Condition | Item |
|---|---|
| Condition [1] | In the disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:
·
With all doors closed and engine hood closed, all doors are locked by wireless operation or the entry and start system. |
| Condition [2] | ·
Allow approx. 30 seconds to elapse. |
| Condition [3] | ·
All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation*. ·
Any door is unlocked. ·
Any door is opened. ·
The power switch is turned on (ACC or IG). ·
The auxiliary battery is reconnected. |
| Condition [4] | ·
The engine hood is opened when the engine hood is closed. ·
The auxiliary battery is reconnected. ·
Any door is opened when all doors are closed. ·
Any door is unlocked when all doors are locked. ·
When 5 seconds or more have elapsed after the power switch is pressed, the power source mode is changed to on (IG) without pressing the power switch. ·
The engine hood is opened. ·
Any door is unlocked. ·
Any door is opened. |
| Condition [5] | ·
The power switch is turned on (READY). ·
All doors are unlocked by wireless operation, the entry and start system or key linked power door lock operation*. ·
The power switch is turned on (ACC or IG) within 5 seconds after the power switch was pushed. |
| Condition [6] | ·
After approx. 27.5 seconds, alarm stops and 5 seconds later system returns to armed state. |
| Condition [7] | ·
The engine hood is closed when the engine hood is opened. |
| Condition [8] | ·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
The power switch is pushed. ·
The power switch is turned on (ACC or IG). ·
The auxiliary battery is reconnected. ·
All doors are unlocked by wireless operation, entry and start system or key linked power door lock operation*. |
| Condition [9] | In the disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:
·
With all doors closed and the engine hood open, all doors are locked by wireless operation, the entry and start system or key linked power door lock operation*. |
| Condition [10] | ·
The engine hood is open. |
*: This function is set through the customize function (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>CUSTOMIZE PARAMETERS).
FORCED DOOR LOCK CONTROL
The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (alarm starts), all doors are forced to lock by a forced door lock signal.
Conditions that force the doors to lock:
The theft deterrent system is in the alarm sounding state of active arming mode.
Any door is unlocked.
SECURITY INDICATOR OUTPUT
The main body ECU (multiplex network body ECU) outputs a signal to turn on the security indicator light, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the main body ECU (multiplex network body ECU).
| State of Theft Deterrent System | Security Indicator Light | |
|---|---|---|
| Output Signal from Main Body ECU (Multiplex Network Body ECU) | Actual Lighting Condition | |
| Disarmed state (1), (2) | OFF | OFF (Engine immobiliser system unset)
BLINKING (Engine immobiliser system set) |
| Arming preparation state | ON | ON |
| Armed state | OFF | BLINKING |
| Alarm sounding state | ON | ON |
| Time | Security Indicator |
|---|---|
| 0.125 sec. | ON |
| 1.875 sec. | OFF |
When the engine immobiliser system is set, the security indicator light blinks during both the disarmed state and the armed state, due to output signals from the engine immobiliser system.