Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2020.08
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch EV Mode Circuit  


DESCRIPTION

The EV mode signal is sent to the hybrid vehicle control ECU. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter sub-assembly to illuminate the EV indicator light.

WIRING DIAGRAM

A259907E40
4.769,2.841 6.615,3.039 1.846,0.198 10 Hybrid Vehicle Control ECU 4.769,2.687 5.152,2.885 0.383,0.198 10 L5 5.185,2.099 5.758,2.338 0.573,0.239 10 EVSW 4.849,2.013 5.157,2.266 0.309,0.253 10 15 1.43,1.174 3.551,1.329 2.121,0.154 10 Combination Meter Sub-assembly 1.304,2.603 1.696,2.787 0.392,0.184 10 L143 1.29,2.757 3.550,3.132 2.260,0.374 10 EV drive mode switch (Combination Switch Assembly) 0.6,3.33 2.446,3.541 1.846,0.211 10 : CAN Communication 1.851,1.987 2.215,2.218 0.364,0.231 10 E 3.041,1.987 3.392,2.231 0.350,0.244 10 S 3.252,1.987 3.588,2.180 0.336,0.194 10 7 1.619,1.987 1.727,2.180 0.107,0.194 10 3

CAUTION / NOTICE / HINT

If any of the following conditions are not met, EV mode may not be turned on or the mode may be canceled. (A buzzer sounds to indicate that the transition to EV mode is canceled.)

EV Mode Entry Condition Tester Display Specified Condition
HV battery charge level State of Charge (All Bat) Approximately 50% or higher
Accelerator pedal position Accelerator Degree Below approximately 30%
Engine coolant temperature Engine Coolant Temp 0°C (32°F) or higher
HV battery temperature Temp of Batt TB1 to TB3 Between 10 to 40°C (50 to 104°F)
Vehicle speed
(Varies depending on engine warm-up condition)
Vehicle Spd Cold: 30 km/h (19 mph) or less
Warmed-up: 45 km/h (28 mph)
Win Charge Control Value Below -20 kW
Wout Discharge Control Value 20 kW or higher
Defroster - OFF
Cruise control - OFF

PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
a.

Check if a buzzer sounded when attempting to enter EV mode.

Result:
Result Proceed to
No buzzer sounded. A
A buzzer sounded. B



HINT:

If a buzzer sounds, one or more of the EV mode entry conditions have not been met. Check that all of the EV mode entry conditions have been met before pressing the EV drive mode switch (Combination Switch Assembly).



A

2.READ VALUE USING GTS (CAN BUS CHECK)

B

COMPLETED

2.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / CAN Bus Check.

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B



d.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / Health Check.


d.

Check DTCs.

Result
Result Proceed to
No DTCs are output. A
DTCs are output. B


e.

Turn the power switch off.



A

4.PERFORM ACTIVE TEST USING GTS (INDICAT. EV MODE)

B

GO TO DTC CHART

4.PERFORM ACTIVE TEST USING GTS (INDICAT. EV MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. EV Mode.


d.

Perform the "Indicat. EV Mode" Active Test.

OK:

The EV mode indicator light comes on or blinks.


Result:
Result Proceed to
OK A
NG (w/o Multi-information Display) B
NG (w/ Multi-information Display) C



e.

Turn the power switch off.



A

5.READ VALUE USING GTS (EV REQUEST, EV SWITCH)

B

C

REPLACE COMBINATION METER SUB-ASSEMBLY

5.READ VALUE USING GTS (EV REQUEST, EV SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / EV request, EV Switch.


d.

Read the value displayed on the GTS.

Tester Display Measurement Item/Range Normal Condition
EV request EV mode transition availability/
ON or OFF
In EV mode: ON
EV Switch EV drive mode switch (Combination Switch Assembly) condition/
ON or OFF
EV drive mode switch (Combination Switch Assembly) being pushed and held: ON

Result:
Result Proceed to
The GTS display changes according to the EV drive mode switch (Combination Switch Assembly) operation. A
The GTS display does not change according to the EV drive mode switch (Combination Switch Assembly) operation. B



e.

Turn the power switch off.



A

B

6.CHECK EV DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY)
6.CHECK EV DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY)
a.

Remove the EV drive mode switch (combination switch assembly).


b.
A253200E17
0.839,0.173 0.991,0.334 0.151,0.161 10 *a 1.384,1.737 1.496,1.898 0.112,0.161 10 S 1.858,1.737 1.967,1.898 0.110,0.161 10 E 1.642,1.225 1.449,1.721 false 1.681,1.029 1.906,1.721 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (S) - 3 (E) EV drive mode switch (Combination Switch Assembly) being pushed and held Below 1 Ω
EV drive mode switch (Combination Switch Assembly) not pushed 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(EV Drive Mode Switch (Combination Switch Assembly))

c.

Install the EV drive mode switch (combination switch assembly).



OK

7.CHECK EV DRIVE MODE HARNESS AND CONNECTOR (SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE EV DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY)

7.CHECK EV DRIVE MODE HARNESS AND CONNECTOR (SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the L143 EV drive mode switch (combination switch assembly) connector.


b.
U190675E02
1.854,1.177 2.104,1.823 true 1.042,0.271 1.198,0.438 0.156,0.167 10 false *a 2.083,1.844 2.198,2.01 0.115,0.167 10 false E 0.813,1.042 1.146,1.208 0.333,0.167 10 false L143

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L143-3 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to EV Drive Mode Switch (Combination Switch Assembly))

c.

Reconnect the L143 EV drive mode switch (combination switch assembly) connector.



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY))
a.

Disconnect the L5 hybrid vehicle control ECU connector.


b.

Disconnect the L143 EV drive mode switch (combination switch assembly) connector.


c.
U190790E02
2.521,1.885 2.271,2.323 false 1.833,3.75 1.979,4.115 false 2.448,0.271 2.781,0.542 0.333,0.271 10 false L6 2,2.333 2.479,2.594 0.479,0.26 10 false EVSW 0.604,3.479 0.979,3.75 0.375,0.271 10 false L143 1.948,4.125 2.167,4.281 0.219,0.156 10 false S 0.104,0.094 0.406,0.302 0.302,0.208 10 false *a 0.49,2.406 0.792,2.615 0.302,0.208 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-15 (EVSW) - L143-7 (S) Always Below 1 Ω
L5-15 (EVSW) or L143-7 (S) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to EV Drive Mode Switch (Combination Switch Assembly))

d.

Reconnect the L143 EV drive mode switch (combination switch assembly) connector.


e.

Reconnect the L5 hybrid vehicle control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR