Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2020.08
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Room Temperature Sensor Room temperature sensor (cooler thermistor) /
Min.: -6.50°C (20.30°F)
Max.: 57.25°C (135.05°F)
Actual cabin temperature displayed -
Ambient Temp Sensor Ambient temperature sensor (thermistor assembly) /
Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Adjusted Ambient Temp Adjusted ambient temperature /
Min.: -30.80°C (-23.44°F)
Max.: 50.80°C (123.44°F)
- -
Evaporator Fin Thermistor Evaporator temperature sensor (No. 1 cooler thermistor) /
Min.: -29.70°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed -
Evaporator Target Temp Evaporator target temperature /
Min.: -327.68°C (-557.82°F)
Max.: 327.67°C (621.81°F)
Evaporator target temperature displayed -
Solar Sensor (D Side) Solar sensor (automatic light control sensor) /
Min.: 0
Max.: 255
Solar sensor value increases as brightness increases -
Engine Coolant Temp Engine coolant temperature sensor /
Min.: 1.30°C (34.34°F)
Max.: 90.55°C (194.99°F)
Actual engine coolant temperature displayed -
Set Temperature (D Side) Set temperature /
Min.: MAX COLD
Max.: MAX HOT
Actual set temperature displayed -
Blower Motor Speed Level Blower motor speed level /
Min.: 0
Max.: 31
Displayed speed level increases in range between 0 and 31 as blower motor speed increases -
Regulator Pressure Sensor Air conditioner pressure sensor /
Min.: -0.4566 MPaG
Max.: 3.2943 MPaG
Actual regulator pressure displayed -
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix) target pulse /
Min.: 0
Max.: 255
MAX. COLD: 6 (pulse)
MAX. HOT: 93 (pulse)
-
Air Mix Servo Actual Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix) actual pulse /
Min.: 0
Max.: 255
MAX. COLD: 6 (pulse)
MAX. HOT: 93 (pulse)
-
Air Outlet Servo Pulse (D) No. 2 air conditioning radiator damper servo sub-assembly (air outlet) target pulse /
Min.: 0
Max.: 255
FACE: 47 (pulse)
B/L: 37 (pulse)
FOOT: 17 to 23 (pulse)
FOOT/DEF: 9 (pulse)
DEF: 5 (pulse)
-
Air Outlet Servo Actu Pulse (D) No. 2 air conditioning radiator damper servo sub-assembly (air outlet) actual pulse /
Min.: 0
Max.: 255
FACE: 47 (pulse)
B/L: 37 (pulse)
FOOT: 17 to 23 (pulse)
FOOT/DEF: 9 (pulse)
DEF: 5 (pulse)
-
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly (air inlet) target pulse /
Min.: 0
Max.: 255
for LHD:

RECIRCULATION: 19 (pulse)

FRESH: 7 (pulse)


for RHD:

RECIRCULATION: 7 (pulse)

FRESH: 25 (pulse)


-
Air Inlet Damper Actual Pulse No. 1 blower damper servo sub-assembly (air inlet) actual pulse /
Min.: 0
Max.: 255
for LHD:

RECIRCULATION: 19 (pulse)

FRESH: 7 (pulse)


for RHD:

RECIRCULATION: 7 (pulse)

FRESH: 25 (pulse)


-
Compressor Speed Compressor speed /
Min.: 0 rpm
Max.: 65535 rpm
Actual compressor speed in range between 0 rpm and 7500 rpm displayed -
Compressor Target Speed Compressor target speed /
Min.: 0 rpm
Max.: 65535 rpm
Target compressor speed in range between 0 rpm and 7500 rpm displayed -
Shift Set Temperature Shift set temperature / 2C decr, 1C decr, Normal, 1C incr or 2C incr Customized value displayed -
Air Inlet Mode Air inlet mode / Auto or Manual Customized value displayed -
Noise and Vibration Reduction Noise and vibration reduction / ON or OFF Customized value displayed -
ECO MODE Cancel ECO MODE cancel / ON or OFF Customized value displayed -
ECO Switch ECO switch /
OFF or ON
ECO mode switch operated: ON
(when switch is pressed)
-
ECO mode switch not operated: OFF
(when switch is not pressed)
Foot/DEF Auto Mode Foot/DEF auto mode / ON or OFF Customized value displayed -
Foot/DEF Auto Blow Up Foot/DEF auto blow up / ON or OFF Customized value displayed -
Ambient Temperature Shift Ambient temperature shift / 3C decr, 2C decr, 1C decr, Normal, 1C incr, 2C incr or 3C incr Customized value displayed -
Compressor Drive Check Compressor drive check /
OK or NG
NG: Compressor does not drive
OK: Compressor drives
-
Number of Trouble Codes Number of trouble codes /
Min.: 0
Max.: 255
Number of DTCs displayed -



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus:

i.

for Air Conditioner: Body Electrical / Air Conditioner / Active Test.


ii.

for Engine and ECT: Powertrain / Engine and ECT / Active Test.



f.

Check the operation by referring to the table below.

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Blower Motor Blower motor with fan sub-assembly Min.: 0, Max.: 31 -
Compressor Target Speed Compressor target speed Min.: 0, Max.: 7500 -
Defogger Relay (Rear) Defogger relay OFF, ON -
Water Pump Water pump relay OFF, ON -
Electrical Fan Electrical fan OFF, ON -
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix) pulse Min.: 0, Max.: 255 Operates between 6 to 93 pulses
Air Outlet Servo Pulse (D) No. 2 air conditioning radiator damper servo sub-assembly (air outlet) pulse Min.: 0, Max.: 255 Operates between 5 to 47 pulses
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly (air inlet) pulse Min.: 0, Max.: 255
for LHD:

Operates between 7 to 19 pulses


for RHD:

Operates between 7 to 25 pulses



Engine and ETC
Tester Display Test Part Control Range Diagnostic Note
Control the Electric Cooling Fan Electric cooling fan OFF, ON -