WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS > WHEEL ALIGNMENT STANDARD



PRECAUTION
Standard values indicated by *1 in the specification tables are for vehicles with a white identification mark on the bottom of the rear coil spring.
C253259E01
Text in Illustration 
*a
Colored identification mark on the bottom of the rear coil spring

MEASURE VEHICLE HEIGHT

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.
  5. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.



  2. C249970E01
  3. Measure the vehicle height.

    Measurement points:
    1. A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
    2. B: Ground clearance of rear axle beam bushing set bolt center
    3. C: Ground clearance of front wheel center
    4. D: Ground clearance of rear wheel center

    Vehicle Height (Unloaded Vehicle) 
    Tire Size
    Model
    Front C - A
    Rear D - B
    175/65R15
    NHP10L-AHXRBA
    96 mm (3.78 in.)
    91 mm (3.58 in.) *1
    32 mm (1.26 in.)
    27 mm (1.06 in.) *1
    NHP10L-AHXVBA
    NHP10L-AHXGBA
    98 mm (3.86 in.)
    94 mm (3.70 in.) *1
    34 mm (1.34 in.)
    30 mm (1.18 in.) *1
    195/50R16
    -
    99 mm (3.90 in.)
    35 mm (1.38 in.)
    1. *1: Vehicles with a white identification mark on the bottom of the rear coil spring


INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:
Inspect while the vehicle is unloaded.



    C132440E21
  1. Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
    Text in Illustration 
    *1
    Turning Radius Gauge
    *2
    Camber-caster-kingpin Gauge

  2. Inspect the camber, caster and steering axis inclination.

    Camber (Unloaded Vehicle) 
    Tire Size
    Model
    Camber Inclination
    Right-left Difference
    175/65R15
    NHP10L-AHXRBA
    -0°14' +/- 0°45' (-0.23° +/- 0.75°)
    -0°11' +/- 0°45' (-0.18° +/- 0.75°) *1
    0°30' (0.50°) or less
    NHP10L-AHXVBA
    NHP10L-AHXGBA
    -0°16' +/- 0°45' (-0.27° +/- 0.75°)
    -0°14' +/- 0°45' (-0.23° +/- 0.75°) *1
    195/50R16
    -
    -0°16' +/- 0°45' (-0.27° +/- 0.75°)

    1. *1: Vehicles with a white identification mark on the bottom of the rear coil spring

    Caster (Unloaded Vehicle) 
    Tire Size
    Model
    Caster Inclination
    Right-left Difference
    175/65R15
    NHP10L-AHXRBA
    4°56' +/- 0°45' (4.93° +/- 0.75°)
    4°51' +/- 0°45' (4.85° +/- 0.75°) *1
    0°30' (0.50°) or less
    NHP10L-AHXVBA
    NHP10L-AHXGBA
    4°57' +/- 0°45' (4.95° +/- 0.75°)
    4°53' +/- 0°45' (4.88° +/- 0.75°) *1
    195/50R16
    -
    4°59' +/- 0°45' (4.98° +/- 0.75°)
    1. *1: Vehicles with a white identification mark on the bottom of the rear coil spring

    Steering Axis (Unloaded Vehicle) 
    Tire Size
    Model
    Steering Axis Inclination Reference
    175/65R15
    NHP10L-AHXRBA
    11°28' (11.47°)
    11°22' (11.37°) *1
    NHP10L-AHXVBA
    NHP10L-AHXGBA
    11°31' (11.52°)
    11°26' (11.43°) *1
    195/50R16
    -
    11°32' (11.53°)
    1. *1: Vehicles with a white identification mark on the bottom of the rear coil spring


INSPECT TOE-IN (FRONT)

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Release the parking brake and move the shift lever to N.

  3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)



  4. C188968E05
  5. Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  6. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



  7. C188969E05
  8. Measure the distance between the tread center marks on the front side of the wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle
    Toe-in (Unloaded Vehicle) 
    Specified Condition
    C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°)
    B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.
    If the toe-in is not within the specified range, adjust it at the rack ends.


INSPECT WHEEL ANGLE
C132439E11
  1. Put tread center marks on the rearmost points of a turning radius gauge.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front of the Vehicle

  2. Turn the steering wheel fully to the left and right and measure the turning angle.

    NOTICE:
    Inspect while the vehicle is unloaded.


    Wheel Angle (Unloaded Vehicle) 
    Tire Size
    Model
    Inside Wheel
    Outside Wheel Reference
    175/65R15
    NHP10L-AHXRBA
    40°45' +/- 2° (40.75° +/- 2°)
    40°52' +/- 2° (40.87° +/- 2°) *1
    35°05' (35.08°)
    35°13' (35.22°) *1
    NHP10L-AHXVBA
    NHP10L-AHXGBA
    40°42' +/- 2° (40.70° +/- 2°)
    40°47' +/- 2° (40.78° +/- 2°) *1
    35°02' (35.03°)
    35°08' (35.13°) *1
    195/50R16
    -
    32°32' +/- 2° (32.53° +/- 2°)
    29°28' (29.47°)
    1. *1: Vehicles with a white identification mark on the bottom of the rear coil spring
      If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.


INSPECT CAMBER (REAR)

NOTICE:
Inspect while the vehicle is unloaded.

  1. Install a camber-caster-kingpin gauge.

  2. Inspect the camber.

    Camber (Unloaded Vehicle) 
    Camber Inclination
    Right-left Difference
    -0°58' +/-30' (-0.97° +/- 0.50°)
    -0°57' +/-30' (-0.95° +/- 0.50°) *1
    0°30' (0.50°) or less

    1. *1: Vehicles with a white identification mark on the bottom of the rear coil spring

    HINT:
    Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.


INSPECT TOE-IN (REAR)

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Release the parking brake and move the shift lever to N.

  3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)



  4. C188968E07
  5. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  6. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



  7. C188969E07
  8. Measure the distance between the tread center marks on the front of the wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle) 
    Tire Size
    Specified Condition
    Right-left Difference
    175/65R15
    C + D: 0°21' +/- 15' (0.35° +/- 0.25°)
    C + D: 0°20' +/- 15' (0.33° +/- 0.25°) *1, *2
    C + D: 0°20' +/- 15' (0.33° +/- 0.25°) *1, *3
    0°30' (0.50°) or less
    B - A: 4.0 +/- 3 mm (0.157 +/- 0.118in.)
    B - A: 3.8 +/- 3 mm (0.150 +/- 0.118in.) *1, *2
    B - A: 3.9 +/- 3 mm (0.154 +/- 0.118in.) *1, *3
    6.0 mm (0.236 in.) or less
    195/50R16
    C + D: 0°21' +/- 15' (0.35° +/- 0.25°)
    0°30' (0.50°) or less
    B - A: 4.0 +/- 3 mm (0.157 +/- 0.118in.)
    6.0 mm (0.236 in.) or less

    1. *1: Vehicles with a white identification mark on the bottom of the rear coil spring
    2. *2: NHP10L-AHXRBA
    3. *3: NHP10L-AHXVBA and NHP10L-AHXGBA

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.
    If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.