WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS > PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Each inspection procedure refers to the TOYOTA Repair Manual.

PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Replacement Part
Necessary Procedure
Effect/Inoperative Function when Necessary Procedures are not Performed
ECM
Vehicle Identification Number (VIN) registration
MIL comes on
  1. Throttle with motor body assembly
  2. Cleaning the deposits from the throttle with motor body assembly
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft
    (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Piston or piston ring
  8. Mass air flow meter sub-assembly
  9. Fuel injector assembly
  10. Fuel pump with filter assembly
  11. Air fuel ratio sensor
  12. Engine coolant temperature sensor
  13. Spark plug
  14. Ignition coil assembly
  15. EGR valve assembly
  16. Air leaks from intake system
  17. Gas leaks from exhaust system
  18. Knock control sensor
Inspection after repair
Poor idle, engine starting, etc
  1. Door control and tire pressure monitoring system receiver assembly
  2. Tire pressure warning valve and transmitter
  1. Transmitter ID registration
  2. Initialization
  1. When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
  2. Tire pressure warning function
Brake booster with master cylinder assembly
  1. Initialization and calibration of the linear solenoid valve
  2. Yaw rate and acceleration sensor zero point calibration
  1. ABS warning light illumination
  2. Brake warning light/yellow (minor malfunction) illumination
  3. Slip indicator light illumination
  4. VSC disable or malfunctioning
  1. Brake pedal stroke sensor assembly
  2. Brake pedal
  1. Clearing stored linear solenoid valve calibration data
  2. Initialization and calibration of the linear solenoid valve
Yaw rate and acceleration sensor
(airbag sensor assembly)
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
Power steering ECU assembly
  1. Torque sensor zero point calibration
  2. Assist map writing
  1. P/S warning light comes on
  2. EPS control
Electric power steering column sub-assembly
Torque sensor zero point calibration
Steering effort is different between turning steering wheel to left and right
w/ Smart Key System:
  1. Certification ECU (smart key ECU assembly)
  2. Steering lock ECU (steering lock actuator assembly)
  3. ID code box (immobiliser code ECU)
  4. Power management control ECU
  5. Electrical key transmitter sub-assembly
Code registration (Engine immobiliser system)
  1. Wireless door lock control system
  2. Smart key system
  3. Hybrid control system start
  4. Steering lock system
w/o Smart Key System:
  1. Transponder key ECU assembly
  2. Power management control ECU
  3. Key
Code registration (Engine immobiliser system)
Hybrid control system start
w/o Smart Key System:
  1. Door control transmitter
  2. Door control receiver
Code registration (Wireless door lock control system)
Wireless door lock control system
  1. Occupant detection ECU
  2. Front passenger seat
Zero point calibration and sensitivity check. (Occupant classification system)
  1. Occupant classification system
  2. Passenger airbag ON/OFF indicator
  3. Airbag system (Front passenger side)
  4. Seat belt warning system (Front passenger)
  1. No. 1 air conditioning radiator damper servo sub-assembly
  2. No. 2 air conditioning radiator damper servo sub-assembly
  3. No. 1 blower damper servo sub-assembly
Initialization servo motor (Air conditioning system)
DTCs are output
  1. Door window regulator assembly
  2. Power window regulator motor assembly
  3. Door glass
  4. Door glass run
Initialize power window control system
  1. Auto up/down function
  2. Jam protection function
  3. Operation function after ignition switch is turned off
  1. Sliding roof ECU (sliding roof drive gear assembly)
  2. Sliding roof glass sub-assembly
  3. Sliding roof drive cable sub-assembly
Initialize sliding roof ECU (pulse sensor initial position setting)
  1. Automatic slide open/close and tilt up/down function of sliding roof
  2. Jam protection function
  3. Operation function after ignition switch is turned off
  4. Sliding roof open warning