AIR CONDITIONING SYSTEM > GENERAL



OUTLINE
  1. An automatic air conditioning system is used.

  2. The air conditioning system main components have been made compact, lightweight, and highly efficient to achieve both comfort and good fuel economy at the same time.

  3. The Beneficial Refrigerant Stream (BRS) type No. 1 cooler evaporator sub-assembly, which is beneficial to the reduction of pressure loss, has been provided.


SPECIFICATION
  1. Performance

    Item
    Specification
    Heater
    Heater Output
    W
    4600*
    Air Flow Volume
    m3/h
    280
    Power Consumption
    W
    190
    Cooler
    Cooling Capacity
    W
    4800
    Air Flow Volume
    m3/h
    475
    Power Consumption
    W
    220

    HINT:
    *: Except for the heater output of the PTC heater (quick heater assembly)

  2. Ventilation and Heater Radiator Unit Sub-assembly

    Item
    Specification
    Heater Radiator Unit Sub-assembly
    Type
    Straight Flow Aluminum (SFA)-II
    Size: W x H x L
    mm (in.)
    201.5 x 120 x 27 (7.9 x 4.7 x 1.1)
    Fin Pitch
    mm (in.)
    1.8 (0.07)
    Blower with Fan Motor Sub-assembly
    Motor Type
    K62-12.5T
    Fan Type
    Sirocco
    Fan Size: Dia. x H
    mm (in.)
    145 x 65 (5.7 x 2.6)

  3. Air Conditioning

    Item
    Specification
    Cooler Condenser Assembly
    Type
    Multi-Flow (MF)-IV (Sub Cool)
    Size: W x H x L
    mm (in.)
    620 x 357.4 x 16 (24.4 x 14.1 x 0.6)
    Fin Pitch
    mm (in.)
    3.15 (0.1)
    No. 1 Cooler Evaporator Sub-assembly
    Type
    Beneficial Refrigerant Stream (BRS)
    Size: W x H x L
    mm (in.)
    199.3 x 231 x 38 (7.8 x 9.1 x 1.5)
    Fin Pitch
    mm (in.)
    3.0 (0.1)
    Electric Inverter Compressor (Compressor with Motor Assembly)
    Type
    ES14
    Compressor Oil Type
    ND11
    Refrigerant
    Type
    HFC134a
    Charge Volume
    g
    420+/-30
    Air Refiner Element
    Pollen Removal Type


MAIN FEATURES
  1. The air conditioning system has the following features:

    Item
    Outline
    High Performance
    1. Neural network control is used so passengers can control the air conditioning accurately for maximum comfort.
    2. A pollen removal type air refiner element is used as clean air filter.
    3. The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.
    4. The Positive Temperature Coefficient (PTC) heater control is used. This system contains a PTC heater (quick hater assembly) that heats the air that has passed through the heater radiator unit sub-assembly to ensure proper heater performance.*
    5. An exhaust heat recirculation system is used to improve the heating performance at low temperatures. For details about the exhaust heat recirculation system, see the Exhaust System in the 1NZ-FXE INTAKE/EXHAUST section.
    Lightweight
    A bus connector (air conditioning harness assembly) with a built-in IC is used in a lightweight wire harness design with a reduced number of wires. The use of this connector means that pulse pattern type servo motors are used.
    Compact
    1. A semi-center location air conditioning unit in which the No. 1 cooler evaporator sub-assembly, heater radiator unit sub-assembly and PTC heater (quick hater assembly)* are placed in the vehicle's longitudinal direction is used.
    2. A blower motor with a built-in blower motor controller is used in a compact construction.
    Others
    1. The following parts are used to ensure high cooling or heating performance while realizing a compact and lightweight construction.
      1. Beneficial Refrigerant Stream (BRS) type No. 1 cooler evaporator sub-assembly
      2. Straight Flow Aluminum (SFA)-II type heater radiator unit sub-assembly
      3. Multi-Flow (MF)-IV type cooler condenser assembly
      4. ES14 type electric inverter compressor (compressor with motor assembly)

    1. *: Cold area specification models