AIRBAG SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The airbag system mainly consists of the parts listed in the table below.

    Components
    Outline
    Airbag
    Mainly consists of an inflator and a bag. Upon receiving a deployment signal from the airbag sensor assembly, the inflator generates gas to deploy the bag.
    Front Seat Outer Belt Assembly
    Mainly consists of an inflator and a seat belt. Upon receiving a deployment signal from the airbag sensor assembly, the inflator generates gas to retract the seat belt.
    Airbag Sensor
    Detects the deceleration of the vehicle during a collision, and transmits the signal to the airbag sensor assembly, from which the airbag sensor assembly determines whether ignition is necessary.
    Front Seat Inner Belt Assembly
    Seat Belt Buckle Switch for Driver
    Detects if the driver seat belt is fastened.
    Seat Belt Buckle Switch for Front Passenger
    Detects if the front passenger seat belt is fastened.
    Occupant Classification Sensor
    Detect distortion, and transmit signals corresponding to occupant's weights to the occupant detection ECU.
    Airbag Sensor Assembly
    1. Detects the deceleration of the vehicle during a collision, determines whether ignition is necessary based on the signals from each airbag sensor, and transmits deployment signals to each airbag and seat belt pretensioner.
    2. Provides initial check and diagnosis function.
    Occupant Detection ECU
    Judges whether the front passenger seat is occupied using signals from 2 occupant classification sensors and front passenger seat belt buckle switch.
    SRS Warning Light
    Provided in the combination meter assembly and comes on when the airbag system malfunctions.
    Power Management Control ECU
    1. The power management control ECU receives an airbag deployment signal from the airbag sensor during a frontal collision or side / side rear collision.
    2. The power management control ECU will shut down the hybrid system power supply by turning the System Main Relays (SMRs) off, in order to ensure safety.


OPERATING CONDITION


  1. Ignition Condition

    1. Deceleration sensors used for the airbag system are installed on various parts on the vehicle and transmit the deceleration data of each part during a collision.

    2. Depending on the situation, the airbag sensor assembly sends a deployment signal to each airbag based on the information from each sensor.



    3. Frontal collision signals are produced based on the information from the airbag sensor assembly and front airbag sensors. Frontal collision signals are used to deploy the SRS driver airbag (horn button assembly), SRS front passenger airbag (instrument panel passenger airbag without door assembly), SRS seat cushion airbags (front seat cushion airbag assembly LH/RH), SRS driver knee airbag (lower No. 1 instrument panel airbag assembly) ,SRS Curtain Shield Airbag (Curtain Shield Airbag Assembly LH/RH) and to activate the seat belt pretensioners.


      Y117008E01



    4. Side collision signals are produced based on the combined information from the airbag sensor assembly and a side airbag sensor assembly, No. 2 side airbag sensor assembly or door side airbag sensor. Side collision signals are used to deploy the SRS side airbag (front seat side airbag assembly)*, SRS curtain shield airbag assembly and to activate the seat belt pretensioner*.

      HINT:
      *: If a collision signal is transmitted from a No. 2 side airbag sensor assembly only, a SRS side airbag (front seat side airbag assembly) will not deploy and also a seat belt pretensioner will not be activated.


      Y117009E01



    5. Side rear collision signals are produced based on the combined information from the airbag sensor assembly, a side airbag sensor assembly and No. 2 side airbag sensor assembly. Side rear collision signals are used to deploy the SRS curtain shield airbag assembly.


      Y118466E01


SYSTEM CONTROL


  1. Airbag for Frontal Collision

    1. For frontal collisions, there are 6 airbags and 2 seat belt pretensioners: a SRS driver airbag (horn button assembly), SRS front passenger airbag (instrument panel passenger airbag without door assembly), SRS driver knee airbag (lower No. 1 instrument panel airbag assembly), SRS seat cushion airbag LH (front seat cushion airbag assembly LH), SRS Curtain Shield Airbag LH (Curtain Shield Airbag Assembly LH), SRS Curtain Shield Airbag RH (Curtain Shield Airbag Assembly RH), SRS seat cushion airbag RH (front seat cushion airbag assembly RH), front seat outer belt assembly LH and front seat outer belt assembly RH. The deployment of the airbags and the activation of the seat belt pretensioners occur simultaneously.

    2. The SRS driver airbag (horn button assembly) and the SRS front passenger airbag (instrument panel passenger airbag without door assembly) use dual-stage control. This controls the airbag inflating output by judging the extent of impact and whether or not the seat belt is fastened.

    3. The airbag sensor assembly determines whether the SRS seat cushion airbag LH (front seat cushion airbag assembly LH) should be deployed based on the signals received from the seat belt buckle switch in the front seat inner belt assembly LH.



    4. When the SRS front passenger airbag (instrument panel passenger airbag without door assembly) is deployed, the airbag sensor assembly activates the actuator in response to the signal from the occupant detection ECU to open the front passenger sub-vent hole, regulating the internal pressure of the SRS front passenger airbag (instrument panel passenger airbag without door assembly) to the optimum level.


      Y115300E01



  2. Airbag for Side or Side Rear Collision



    1. For a side collision, if the side airbag sensor assembly and door side airbag sensor detect an impact, it inform the airbag sensor assembly, and the airbag sensor assembly causes the SRS side airbag (front seat side airbag assembly), SRS curtain shield airbag (curtain shield airbag assembly) and seat belt pretensioner to be deployed and operated simultaneously.


      Y115301E01



    2. For a side rear collision, if the No. 2 side airbag sensor assembly detects an impact, it informs the airbag sensor assembly via the side airbag sensor assembly, and the airbag sensor assembly causes the SRS curtain shield airbag (curtain shield airbag assembly) to be deployed.


      Y115302E01



  3. Primary Check Illumination Control



    1. After the ignition switch is turned ON, the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If trouble is detected during the primary check, the SRS warning light remains on even after the 6 seconds have elapsed. See the illustration below.


      Y117005E01


CONSTRUCTION
  1. SRS Driver Airbag (Horn Button Assembly)

    1. The SRS driver airbag (horn button assembly) contains a set of 2 initiators and propellants. The airbag sensor assembly helps optimize the airbag deployment rate by controlling the ignition timing of the initiators.

  2. SRS Front Passenger Airbag (Instrument Panel Passenger Airbag without Door Assembly)

    1. The SRS front passenger airbag (instrument panel passenger airbag without door assembly) contains a set of 2 initiators, propellants and actuator. The airbag sensor assembly helps optimize the airbag deployment rate by controlling the ignition timing of the initiators and the opening/closing of the front passenger sub-vent hole.

  3. SRS Driver Knee Airbag (Lower No. 1 Instrument Panel Airbag Assembly)

    1. The SRS driver knee airbag (lower No. 1 instrument panel airbag assembly) consists of an airbag door, an inflator and a bag.

  4. SRS Seat Cushion Airbag (Front Seat Cushion Airbag Assembly)

    1. The SRS seat cushion airbag (front seat cushion airbag assembly) consists of an inflator and a bag.

  5. SRS Curtain Shield Airbag (Curtain Shield Airbag Assembly)

    1. SRS curtain shield airbags (curtain shield airbag assembly LH/RH) that extend from the front pillar to the roof side rail are installed. Each SRS curtain shield airbag (curtain shield airbag assembly) consists of an inflator and a bag.

  6. SRS Side Airbag (Front Seat Side Airbag Assembly)

    1. SRS side airbags (front seat side airbag assembly LH/RH) are installed in the seat backs of the driver seat and the front passenger seat. Each SRS side airbag (front seat side airbag assembly) consists of an inflator, a bag and a cover.



  7. Front Airbag Sensor



    1. A deceleration sensor is enclosed in the front airbag sensor. Based on the deceleration of the vehicle during a front collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.


      Y117006E01



  8. Side Airbag Sensor Assembly, No. 2 Side Airbag Sensor Assembly and Door Side Airbag Sensor



    1. A deceleration sensor is enclosed in the side airbag sensor assembly, No. 2 side airbag sensor assembly and door side airbag sensor. Based on the deceleration of the vehicle during a side or side rear collision, a distortion is created in the sensor and converted into an electrical signal.


      Y117007E01



  9. Seat Belt Buckle Switch

    1. The built-in seat belt buckle switch of the front seat inner belt assembly detects that the seat belt is fastened.

    2. A non-contact type switch is built into the front seat inner belt assembly on the driver and front passenger sides.

    3. This switch contains a Hall IC and magnet.

    4. The ejector inside the seat belt buckle switch and the plate installed to the ejector move when the seat belt is removed or inserted. The movement of the plate changes the magnetic flux density of the magnet.



    5. The Hall IC detects changes in the magnetic flux density. These changes indicate that the seat belt is either fastened or unfastened, and the Hall IC outputs a signal to the airbag sensor assembly (for driver) or occupant detection ECU (for front passenger).


      Y100045E08


      Text in Illustration 
      *1
      Ejector
      *2
      Magnet
      *3
      Hall IC
      *4
      Plate
      *5
      Magnetic Flux
      -
      -
      *a
      Seat belt not fastened
      *b
      Seat belt fastened


OPERATION


  1. Front Passenger Sub-vent Hole

    1. The airbag sensor assembly activates the actuator in response to signals from the occupant detection ECU.



    2. When the actuator is activated, the pin gets into the inside of the actuator to release the belt, as a result, the front passenger sub-vent hole will open due to the deployment pressure of the SRS front passenger airbag (instrument panel passenger airbag without door assembly).


      Y115304E01


      Text in Illustration (Front Passenger Sub-vent Hole Closed:) 
      *1
      Actuator
      *2
      Belt
      *3
      Bag
      *4
      Pin
      *a
      Front Passenger Sub-vent Hole Closed
      *b
      Actuator Cross Section

      Y115305E01


      Text in Illustration (Front Passenger Sub-vent Hole Open:) 
      *1
      Actuator
      *2
      Belt
      *3
      Bag
      *4
      Pin
      *a
      Front Passenger Sub-vent Hole Open
      *b
      Actuator Cross Section
      V100135
      Pin gets into the inside of the actuator
      V100136
      Releases


DIAGNOSIS
  1. If the airbag sensor assembly detects a malfunction in the airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.

  2. There are 2 types of Diagnostic Trouble Code (DTC) for the airbag system: 5-digit and 2-digit.

  3. The 5-digit DTC can be read by connecting the Techstream to DLC3.

  4. The 2-digit DTC can be read by connecting the SST (09843-18040) to the TC and CG terminals of the DLC3 and reading the blinking of the SRS warning light.



  5. If the SRS airbag deploys, the airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the airbag sensor assembly with a new one.


    Y115306E01