WINDSHIELD GLASS > REMOVAL |
| 1. REMOVE FRONT WIPER ARM HEAD CAP |
![]() |
Using a screwdriver, disengage the 3 claws and remove the front wiper arm head cap.
| *1 | Protective Tape |
| 2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut and front wiper arm and blade assembly LH.
| 3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut and front wiper arm and blade assembly RH.
| 4. REMOVE FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Disengage the 2 clips.
![]() |
Separate the double-sided tape.
| *1 | Double-sided Tape |
| *2 | Clip |
Disengage the 3 guides, and remove the front fender to cowl side seal LH as shown in the illustration.
Disengage the clip from the vehicle.
| 5. REMOVE FRONT FENDER TO COWL SIDE SEAL RH |
| 6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Remove the 2 clips.
Disconnect the washer hose.
Disengage the 5 claws and 3 guides as shown in the illustration.

Disengage the 8 guides and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.

| 7. REMOVE ROOF HEADLINING ASSEMBLY |
| 8. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY |
![]() |
Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.
| *1 | Protective Tape |
![]() |
Using a knife, cut off the moulding as shown in the illustration.
| *1 | Windshield Glass |
| *2 | Moulding |
| *3 | Body |
![]() |
Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.
| *1 | Matchmark |
![]() |
Pass a piano wire between the vehicle body and glass from the interior.
| *1 | Windshield Glass Stopper |
| *2 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.
Disconnect the windshield glass stoppers.

| *A | 1-piece Type | *B | 2-pieceType |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
Using suction cups, remove the windshield glass sub-assembly.
| 9. REMOVE WINDOW GLASS ADHESIVE DAM |
When reusing the windshield glass:
![]() |
Using a scraper, remove the window glass adhesive dam.
| *A | Back Side |
| 10. REMOVE WINDSHIELD OUTSIDE MOULDING |
When reusing the windshield glass:
![]() |
Using a scraper, remove the windshield outside moulding.
| *A | Back Side |
| 11. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type) |
When reusing the windshield glass:
![]() |
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
| *A | Back Side |
| 12. REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
When reusing the windshield glass:
![]() |
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
| *A | Back Side |
| 13. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
![]() |
Remove the 2 No. 1 windshield glass stoppers.
| 14. CLEAN WINDSHIELD GLASS |
When reusing the windshield glass:
![]() |
Using a scraper, remove any adhesive dam and adhesive residue from the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
| 15. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surfaces of the vehicle body.
| *1 | Body |
| *2 | Adhesive |
Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.
Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.