Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS

BACK DOOR GLASS > INSTALLATION

for Preparation Click here



1. INSTALL BACK WINDOW GLASS CLIP LH
  1. Using a brush or sponge, coat the application area of a new back window glass clip LH with primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B298783E01
  1. Install the new back window glass clip LH onto the back door glass as shown in the illustration.
    Text in Illustration 
    *A
    Back Side
    *1
    Ceramic Notch



2. INSTALL BACK WINDOW GLASS CLIP RH
  1. Using a brush or sponge, coat the application area of a new back window glass clip RH with primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B293588E01
  1. Install the new back window glass clip RH onto the back door glass as shown in the illustration.
    Text in Illustration 
    *A
    Back Side
    *1
    Ceramic Notch



3. INSTALL BACK WINDOW GLASS ADHESIVE DAM
  1. Using a brush or sponge, coat the application area of a new back window glass adhesive dam with primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B298788E01
  1. Cut a new back window glass adhesive dam (a) so that it fits to the position specified in the illustration.
    Text in Illustration 
    *A
    Back Side
    *1
    Ceramic Notch for Dam Alignment

    Standard Dimension:

    Area
    Dimension
    a
    1053 mm (3.45384 ft.)
    b
    3.0 mm (0.118 in.)

  1. Install the new back window glass adhesive dam onto the back door glass as shown in the illustration.



    B298789E01
  1. Cut a new back window glass adhesive dam (a) so that it fits to the position specified in the illustration.
    Text in Illustration 
    *A
    Back Side
    *1
    Ceramic Notch for Dam Alignment

    Standard Dimension:

    Area
    Dimension
    a
    1070 mm (3.5096 ft.)
    b
    13.2 mm (0.52 in.)

  1. Install the new back window glass adhesive dam onto the back door glass as shown in the illustration.



4. INSTALL BACK DOOR GLASS SUB-ASSEMBLY


    B296206E01
  1. Position the back door glass sub-assembly.
    Text in Illustration 
    *1
    Matchmark

    1. Using suction cups, place the back door glass sub-assembly in the correct position.

    2. Check that the whole contact surface of the back door glass rim is perfectly even.

    3. Align the matchmarks on the back door glass and vehicle body.

      NOTICE:
      Check that the back door glass clips are attached to the vehicle body correctly.

    4. Remove the back door glass.



  1. Using a brush, coat the installation surface on the vehicle body with Primer M.


    B293592E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    -
    -
    *a
    CORRECT
    *b
    INCORRECT
    *c
    Edge of Curved Surface
    -
    -

    NOTICE:
    1. Do not coat the adhesive with primer M.
    2. Do not apply too much primer M.
    3. Allow the primer M coating to dry for 3 minutes or more.
    4. Throw away any leftover primer M.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



  1. Using a brush or sponge, coat the adhesive application area with primer G.


    B293589E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Primer G
    -
    -

    Standard Dimension:

    Area
    Dimension
    a
    9.0 mm (0.354 in.) or more
    b
    22.0 mm (0.866 in.) or more
    c
    23.9 mm (0.941 in.) or more
    d
    16.0 mm (0.63 in.) or more

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E07
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.
      Text in Illustration 
      *1
      Nozzle

      Standard Dimension:
      Area
      Dimension
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time described in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back door glass as shown in the illustration.


      B293590E01


      Text in Illustration 
      *A
      Back Side
      -
      -
      *1
      Adhesive
      -
      -

      Standard Dimension:

      Area
      Dimension
      a
      5.0 mm (0.197 in.)
      b
      8.0 mm (0.315 in.)
      c
      26.9 mm (1.06 in.)
      d
      5.0 mm (0.197 in.)



  1. Install the back door glass sub-assembly.



      B296206E01
    1. Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.
      Text in Illustration 
      *1
      Matchmark

      NOTICE:
      1. Check that the back window glass clips are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and back door glass.

    2. Lightly press the front surface of the back door glass to ensure a close fit.

      HINT:
      Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.

    3. Using a scraper, remove any excess or protruding adhesive.

    4. Hold the back door glass using protective tape until the applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle for the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time Prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours

  1. Connect each connector.



5. INSPECT FOR LEAKS AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



6. INSTALL REAR SPOILER ASSEMBLY
(Click here)


7. INSTALL BACK DOOR TRIM COVER


    B297007
  1. Engage the 6 clips to install the back door trim cover.



8. INSTALL BACK DOOR TRIM BOARD ASSEMBLY


    B297006
  1. Install the back door trim assembly with the 10 clips.