Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A0D-350    High Voltage System Inter-Lock Circuit High

DTC    P0A0D-351    High Voltage System Inter-Lock Circuit High

for Preparation Click here


DESCRIPTION

  1. When the power management control ECU detects that a safety device (interlock) is operated, such as when the service plug grip, inverter terminal cover or connector cover assembly is removed, it will prohibit hybrid system operation or shut off the system main relay. There are three safety devices in three different locations. The first safety device is located at the service plug grip. The second one is located at the frame wire that is connected to the inverter with converter assembly. The third one is located at the inverter terminal cover where the motor cable is connected to the inverter with converter assembly. If the service plug grip, inverter terminal cover, or frame wire is removed, the interlock signal line will be open. If the vehicle is being driven, this condition will be determined to be an open circuit and the system main relays will not be shut off. If the safety devices are re-installed correctly, the system will return to normal when the ignition switch is turned on (IG).
  2. The system main relay will be turned off from the next trip after the open is detected until the condition returns to normal.

DTC No.
INF Code
DTC Detection Condition
Trouble Are
P0A0D
350
Either of the following conditions is met:
  1. With the vehicle stopped, the service plug grip, inverter terminal cover or another part with a safety device was removed.
  2. With the vehicle stopped, the interlock signal line became open.
(1 trip detection logic)
  1. Wire harness or connector
  2. Power management control ECU
  3. Service plug grip
  4. Inverter with converter assembly
  5. Frame wire
  6. Inverter terminal cover
P0A0D
351
Interlock signal line opens while the vehicle is being driven (at 5 km/h or more)
(1 trip detection logic)

WIRING DIAGRAM


A310026E04


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (IG) and wait for 5 seconds or more.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A0D only is output.
    A
    P0A1D is also output
    B

  1. Turn the ignition switch off.



B
GO TO DTC CHART (P0A1D) (Click here)
A


2.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the ignition switch off.


NEXT


3.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A0D-350 or P0A0D-351 is output again.
    A
    Neither P0A0D-350 or P0A0D-351 is output again.
    B

  1. Turn the ignition switch off.



B
Go to step 10
A


4.CHECK SERVICE PLUG GRIP

CAUTION:
Be sure to wear insulated gloves.



    A314624E01
  1. Check if the service plug grip is installed correctly.
    Text in Illustration 
    *1
    Service Plug Grip

    Standard:
    The service plug grip is fully pushed in as shown in the illustration.

    NOTICE:
    1. Insert the service plug grip until a click sound is heard.
    2. If "UNLOCK" is printed on the service plug grip, push in the service plug grip until "UNLOCK" is not visible at all.

    HINT:
    1. For the removal and installation procedures (Click here).
    2. P0A0D-350 is also set if the ignition switch is turned on (IG) with the service plug grip removed. Confirm the conditions when the malfunction occurred.



NG
INSTALL PARTS CORRECTLY
OK


5.CHECK INVERTER TERMINAL COVER

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



    A258644
  1. Check if the inverter terminal cover of the inverter with converter assembly is installed correctly.

    OK:
    The inverter terminal cover is installed correctly.



NG
INSTALL PARTS CORRECTLY
OK


6.CHECK FRAME WIRE

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



    A258644
  1. Remove the inverter terminal cover from the inverter with converter assembly.



    A258645
  1. Remove the inverter cover from the inverter with converter assembly.



    A258649E08
  1. Check if the frame wire P1 is connected correctly.

    OK:
    The frame wire connector is connected correctly.

  1. Install the inverter cover.

  1. Install the inverter terminal cover.



NG
INSTALL PARTS CORRECTLY
OK


7.CHECK POWER MANAGEMENT CONTROL ECU

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A47 from the inverter with converter assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).



    A215725E70
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-35 (ILKI) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

    NOTICE:
    Turning the ignition switch ON with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the inverter with converter assembly connector.



NG
Go to step 16
OK


8.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERLOCK)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A47 from the inverter with converter assembly.



    A215652E47
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-35 (ILKI) - A47-36 (ILKO)
    Ignition switch off
    10 Ω or less

    Text in Illustration 
    *a
    Component without harness connected
    (Inverter with Converter Assembly)

NOTICE:
Do not remove the inverter cover.

  1. Connect the inverter with converter assembly connector.



NG
Go to step 14
OK


9.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - BODY GROUND)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A47 from the inverter with converter assembly.

  1. Install the service plug grip.



    A215725E71
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-36 (ILKO) - Body ground
    Ignition switch off
    Less than 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

  1. Remove the service plug grip.

  1. Connect the inverter with converter assembly connector.



NG
Go to step 11
OK


10.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
  1. Check the connections of each connector.

    OK:
    Dirt or foreign matter has not entered the connection, and there is no evidence of contamination.



NG
REPAIR OR REPLACE CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

11.CHECK SERVICE PLUG GRIP
  1. Remove the service plug grip.



    A314958E01
  1. Check the condition of the service plug grip interlock.
    Text in Illustration 
    *1
    Service Plug Grip

    OK:
    Dirt or foreign matter has not entered the connection, and there is no evidence of contamination.



    A314624E01
  1. Install the service plug grip.

    NOTICE:
    1. Insert the service plug grip until a click sound is heard.
    2. If "UNLOCK" is printed on the service plug grip, push in the service plug grip until "UNLOCK" is not visible at all.

    Text in Illustration 
    *1
    Service Plug Grip



NG
REPLACE SERVICE PLUG GRIP (Click here)
OK


12.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



    A267575E01
  1. Check that the interlock connector at the service plug grip installation socket is connected correctly.
    Text in Illustration 
    *1
    Interlock Connector

    OK:
    The connector is connected correctly.



NG
INSTALL PARTS CORRECTLY
OK


13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - SERVICE PLUG GRIP)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A47 from the inverter with converter assembly.

  1. Disconnect connector M42 from the service plug.



    A267576E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-36 (ILKO) - M42-1 (ILK)
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Front view of wire harness connector
    (to Service Plug Grip)

  1. Connect the service plug grip connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - SERVICE PLUG GRIP)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SERVICE PLUG GRIP - BODY GROUND) 

14.CHECK INVERTER TERMINAL COVER

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



    A258644
  1. Remove the inverter terminal cover from the inverter with converter assembly.



    A268140
  1. Check the condition of the inverter terminal cover interlock.

    OK:
    Dirt or foreign matter has not entered the connection, and there is no evidence of contamination.

  1. Install the inverter terminal cover.



NG
REPLACE INVERTER TERMINAL COVER (Click here)
OK


15.CHECK FRAME WIRE (FRAME WIRE CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



    A258644
  1. Remove the inverter terminal cover from the inverter with converter assembly.



    A258645
  1. Remove the inverter cover from the inverter with converter assembly.



    A258649E08
  1. Disconnect the frame wire P1 from the inverter with converter assembly.



    A215624
  1. Check the frame wire interlock.

    OK:
    Dirt or foreign matter has not entered the connection, and there is no evidence of contamination.

  1. Connect the frame wire to the inverter with converter assembly.

  1. Install the inverter cover.

  1. Install the inverter terminal cover.



NG
REPLACE FRAME WIRE (Click here)
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

16.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A47 from the inverter with converter assembly.



    A217808E06
  1. Disconnect connector A38 from the power management control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-32 (ILK) - A47-35 (ILKI)
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

  1. Connect the power management control ECU connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)