Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Main Body / Data List.

  5. Read the Data List according to the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Ignition switch ACC signal/ON or OFF
    ON: Ignition switch ACC
    OFF: Ignition switch off
    -
    IG SW
    Ignition switch ON (IG) signal/ON or OFF
    ON: Ignition switch ON (IG)
    OFF: Ignition switch off
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal/ON or OFF
    ON: Rear door RH open
    OFF: Rear door RH closed
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal/ON or OFF
    ON: Rear door LH open
    OFF: Rear door LH closed
    -
    Back Door Courtesy SW
    Back door courtesy switch signal/ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    FR Door Lock Pos
    Front door RH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    -
    FR Door Courtesy SW
    Front door courtesy light switch RH signal/ON or OFF
    ON: Front door RH open
    OFF: Front door RH closed
    -
    FL Door Lock Pos
    Front door LH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    -
    FL Door Courtesy SW
    Front door courtesy light switch LH signal/ON or OFF
    ON: Front door LH open
    OFF: Front door LH closed
    -
    RR-Door Lock Pos SW*1
    Rear door RH unlock detection switch signal/ON or OFF
    ON: Rear door LH locked and rear door RH unlocked
    ON: Rear door LH unlocked and rear door RH locked
    ON: Rear door LH and rear door RH unlocked
    OFF: Rear door LH and rear door RH locked
    -
    RL-Door Lock Pos SW*1
    Rear door LH unlock detection switch/ON or OFF
    ON: Rear door LH locked and rear door RH unlocked
    ON: Rear door LH unlocked and rear door RH locked
    ON: Rear door LH and rear door RH unlocked
    OFF: Rear door LH and rear door RH locked
    -
    I/L ON W/Door Key Unlock
    Function that lights up the interior lights when the doors are unlocked/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    Lighting Time
    Lighting time of the delay control function (illuminated entry system)/15s, 7.5s or 30s
    15s: 15 seconds
    7.5s: 7.5 seconds
    30s: 30 seconds
    Customized value is displayed
    Room Light when Aprchd*1
    Function that lights up the interior lights when a key enters any actuation area/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    I/L when ACC OFF
    Function that lights up the interior lights when the ignition switch is turned from ACC or ON (IG) to off/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed

    1. *1: w/ Smart Key System


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / (desired system) / Active Test.

  5. Perform the Active Test according to the display on the Techstream.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Personal light and power switch illumination*1
    ON/OFF
    Interior light door switch DOOR
    Relay for Interior Light Auto Cut Function
    DOME CUT Relay
    ON/OFF
    -

    Smart Key*1 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power/Engine SW Light
    Power switch light
    OFF/ON
    When performing this Active Test, make sure the following condition is met:
    The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.

    1. *1: w/ Smart Key System