Home › Engine / Hybrid System › 1NZ-FXE COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE WATER PUMP ASSEMBLY
  1. Install a new gasket.

    HINT:
    Be sure to clean the contact surfaces.

  1. Install the engine water pump assembly with the 5 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 clamps.

  1. Connect the connector.

    NOTICE:
    Do not start the engine water pump assembly before adding coolant.



2. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner case sub-assembly with the 2 bolts and grommet.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the air cleaner filter element sub-assembly.



3. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A267399E01
  1. Install the air cleaner hose sub-assembly and lock the hose clamp.
    Text in Illustration 
    *a
    Engine Side
    *b
    75°

    NOTICE:
    1. Align the groove of the air cleaner hose with the tab of the throttle with motor body assembly and install the hose.
    2. Make sure that the tab of the air cleaner hose clamp stays within the range shown by *b.

  1. Install the air cleaner cap sub-assembly with the 2 clamps.

  1. Connect the wire harness clamp.

  1. Connect the mass air flow meter connector.

  1. Connect the purge VSV.

  1. Connect the ventilation hose.



4. ADD COOLANT (for Engine)


    A267961E01
  1. Insert the engine drain cock plug.
    Text in Illustration 
    *1
    Hose

  1. Disconnect the hose from the engine drain cock plug.

  1. Install the stop ring.

  1. Tighten the radiator drain cock plug by hand.



    A206788E05
  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Coolant level should be within 20 mm (0.787 in.) from the filler tube end.)
    Text in Illustration 
    *a
    Filler Tube End
    *b
    Coolant Level
    *c
    20 mm

    Standard Capacity:
    5.2 liters (5.5 US qts, 4.6 lmp. qts)

    NOTICE:
    Never use water as a substitute for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Remove the reserve tank cap.



    A275622E01
  1. Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
    Text in Illustration 
    *a
    Full Line
    *b
    Low Line

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the water filler cap sub-assembly and reserve tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to the low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

    2. Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the cooling fan.

      NOTICE:
      1. Make sure that the radiator reserve tank assembly still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reserve tank assembly does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reserve tank assembly is filled to the full line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the full line on the radiator reserve tank assembly.



5. INSPECT FOR COOLANT LEAK (for Engine)

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A268671
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator, engine water pump, front exhaust pipe assembly and engine coolant temperature sensor for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.