Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > Blower Motor Circuit

for Preparation Click here


DESCRIPTION

The blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly. Blower motor speed signals are transmitted in accordance with changes in the duty ratio.

WIRING DIAGRAM


E229256E09


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.


Air Conditioner 
Tester Display
Test Part
Control Range
Diagnostic Note
Blower Motor
Blower motor with fan sub-assembly
Min.: 0, Max.: 31
-

Result:

Result
Proceed to
OK
A
NG (blower motor does not operate)
B
NG (blower motor operates but does not change speed)
C



B
Go to step 2

C
Go to step 6
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)
  1. Disconnect the G32 blower motor with fan sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G32-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - POWER SOURCE)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G32-3 (+B) - Body ground
    Ignition switch off
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
  1. Disconnect the G34 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G34-22 (BLW) - G32-2 (SI)
    Always
    Below 1 Ω
    G34-22 (BLW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
  1. Reconnect the G32 blower motor with fan sub-assembly connector.



    E221028E12
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G34-22 (BLW) - Body ground
    Ignition switch off
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY (Click here)
OK


6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY


    E227501E06
  1. Remove the air conditioning amplifier assembly (Click here).

  1. Reconnect the G34 air conditioning amplifier assembly connector.

  1. Turn the ignition switch to ON (IG).

  1. Turn the blower switch on (LO).

  1. Measure the waveform between terminal G34-22 (BLW) of the air conditioning amplifier assembly and body ground.

    OK:
    Waveform is similar to that shown in the illustration.

    HINT:
    The waveform varies with the blower speed.

Item
Content
Tool setting
1 V/DIV., 500 μs/DIV.
Vehicle condition
Ignition switch ON (IG)
Blower switch on (LO)
Text in Illustration 
*a
Component with harness connected
(Air Conditioning Amplifier Assembly)


NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY (Click here)