Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR

STEERING GEAR > INSTALLATION

for Preparation Click here



1. INSTALL TIE ROD END SUB-ASSEMBLY LH


    C187022E04
  1. Install the lock nut and tie rod end sub-assembly LH to the steering gear assembly until the matchmarks are aligned.
    Text in Illustration 
    *a
    Matchmark

    HINT:
    After adjusting the toe-in, tighten the lock nut.



2. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



3. INSTALL STEERING LINK ASSEMBLY


    C244486
  1. Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    79 N*m{ 800 kgf*cm , 58 ft.*lbf }

    NOTICE:
    1. Keep the nut from rotating while turning the bolt because the nut has its own stopper.
    2. Make sure to tighten the bolts starting from the right side of the vehicle.



4. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
  1. Install the No. 1 steering column hole cover subassembly to the steering link assembly.



5. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

    NOTICE:
    1. Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.
    2. Use the attachments to keep the front suspension crossmember sub-assembly level.
    3. The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.

  1. Temporarily tighten the front suspension crossmember sub-assembly to the body with the 6 bolts.



  1. Tighten the 2 bolts A, 2 bolts B and 2 bolts C on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.


    C249877E01

    SST
    09670-00010  

    Text in Illustration 
    *a
    OK
    *b
    NG
    V100136
    Front of the Vehicle
    -
    -

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt B:
    151 N*m{ 1540 kgf*cm , 111 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

  1. Lower the engine lifter.

  1. Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



6. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
  1. Install the front lower No. 1 suspension arm sub-assembly LH to the steering knuckle with a new nut.

    Torque:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    Prevent oil from adhering to the threaded and tapered parts.

  1. Install a new clip.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the clip are not aligned.



7. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



8. CONNECT TIE ROD END SUB-ASSEMBLY LH


    C249933
  1. Connect the tie rod end sub-assembly LH to the steering knuckle with a new nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.

  1. Install a new cotter pin.



9. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY LH
  1. Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    Use a hexagon socket wrench to hold the stud.



11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



12. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C251686E02
  1. Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.
    Text in Illustration 
    *a
    Lip

    NOTICE:
    Make sure that the lip of the No. 1 steering column hole cover sub-assembly is not damaged.



13. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY


    C249572E03
  1. Install the steering sliding yoke sub-assembly to the steering gear assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    1. Align the matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.
    2. When the steering sliding yoke sub-assembly is replaced with a new one, it has no matchmarks, so install it while the head of the bolt B faces the back of the vehicle.

  1. Install bolt B.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



14. INSTALL COLUMN HOLE COVER SILENCER SHEET


    C248046
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



15. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



16. POSITION WHEELS FACING STRAIGHT AHEAD


17. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



18. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)