Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER

FRONT SUSPENSION MEMBER > REMOVAL

for Preparation Click here



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. SECURE STEERING WHEEL


    C247537
  1. Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.



3. REMOVE COLUMN HOLE COVER SILENCER SHEET


    C248046
  1. Remove the 2 clips and the column hole cover silencer sheet.



4. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


    C249572E01
  1. Put matchmarks on the steering sliding yoke sub-assembly and steering gear assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Loosen bolt A.

  1. Remove bolt B.

  1. Separate the steering sliding yoke sub-assembly from the steering gear assembly.



5. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C251686E01
  1. Remove clip A, detach clip B from the body and disconnect the No. 1 steering column hole cover sub-assembly.

    NOTICE:
    Do not damage clip B.



6. REMOVE FRONT WHEEL


7. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C249871
  1. Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.

    HINT:
    Use a hexagon socket wrench to hold the stud.



8. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



9. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and nut.



    C249937E01
  1. Install SST to the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper end of the tie rod end and SST are aligned.

  1. Secure SST using a string.

    NOTICE:
    Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



  1. Using SST, separate the tie rod end from the steering knuckle.

    SST
    09960-20010   (09961-02060)


    C249935E01


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Grease Application Area
    *c
    Place the wrench here.
    -
    -

    CAUTION:
    Apply grease to the bolt threads and the tip of SST.

    NOTICE:
    1. Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.
    2. Be sure to place the wrench on the part indicated in the illustration.
    3. Do not damage the front disc brake dust cover.
    4. Do not damage the ball joint dust cover.
    5. Do not damage the steering knuckle.



10. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



11. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    C107513
  1. Remove the clip and nut.



    C172759E06
  1. Install SST to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the threaded section of the lower ball joint and SST are aligned.



  1. Using SST, separate the front lower No. 1 suspension arm sub-assembly LH from the steering knuckle.

    SST
    09960-20010   (09961-02010, 09961-02060)


    C236386E01


    Text in Illustration 
    *a
    Apply grease
    *b
    Place wrench here

    CAUTION:
    Apply grease to the threads and end of the SST bolt.

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the lower ball joint dust cover.
    5. Do not damage the drive shaft outboard joint boots.
    6. Do not damage the front disc brake dust cover.
    7. Do not damage the steering knuckle.



12. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



13. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C249868E01
  1. Using a jack and a wooden block, support the engine and transaxle assembly.
    Text in Illustration 
    *1
    Jack
    *2
    Wooden Block
    V100135
    Front of the Vehicle



    C249869
  1. Remove the bolt and separate the engine moving control rod.



    C249867E01
  1. Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
    Text in Illustration 
    *1
    Engine Lifter
    *2
    Attachment
    V100135
    Front of the Vehicle
    V100155
    Attachment Placement Location

    NOTICE:
    1. Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.
    2. Use the attachments to keep the front suspension crossmember sub-assembly level.
    3. The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.



  1. Remove the 6 bolts and front suspension crossmember sub-assembly.


    C249876

  1. Slowly lower the front suspension crossmember sub-assembly.

    NOTICE:
    When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



14. REMOVE STEERING LINK ASSEMBLY


    C244486
  1. Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

    NOTICE:
    Keep the nut from rotating while turning the bolt because the nut has its own stopper.



15. REMOVE FRONT NO. 1 STABILIZER BRACKET LH


    C249885
  1. Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front suspension crossmember sub-assembly.



16. REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.



17. REMOVE FRONT STABILIZER BAR


18. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    C235698
  1. Remove the bolt and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.



19. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



20. REMOVE ENGINE MOVING CONTROL ROD COVER (for Cold Area Specification Vehicles)


    C235697
  1. Remove the 2 clips and engine moving control rod cover from the front suspension crossmember sub-assembly.



21. REMOVE ENGINE MOVING CONTROL ROD


    C213122
  1. Remove the bolt and engine moving control rod from the front suspension crossmember sub-assembly.