Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR

REAR AIRBAG SENSOR > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. INSTALL SIDE NO. 2 AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



  1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296256E01


    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

  1. Insert the pin (stopper) into the body hole and install the side No. 2 airbag sensor assembly to the vehicle body with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the side No. 2 airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the side No. 2 airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the bolt while holding the side No. 2 airbag sensor assembly because the side No. 2 airbag sensor assembly pin (stopper) is easily damaged.



  1. Connect the connector to the side No. 2 airbag sensor assembly.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).


      C198070E09


      Text in Illustration 
      *1
      White Housing Lock
      -
      -
      *a
      Slide
      -
      -

      HINT:
      When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the side No. 2 airbag sensor assembly.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY
w/o Package Tray Trim:
w/ Package Tray Trim:


3. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)
  1. Connect the connector.



    E288706
  1. Engage the claw to install the No. 1 luggage compartment light assembly.



4. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
  1. Engage the 2 claws.

  1. Install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



5. INSTALL REAR DECK TRIM COVER
  1. Engage the 2 guides and 4 claws.

  1. Install the rear deck trim cover with the 2 clips.



6. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
  1. Install the package tray trim panel assembly.



7. INSTALL SPARE WHEEL CUSHION
  1. Install the 2 spare wheel cushions.



8. INSTALL REAR FLOOR MAT ASSEMBLY
  1. Install the rear floor mat assembly.



9. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


10. INSTALL REAR DOOR SCUFF PLATE
  1. Engage the guide and the 5 claws to install the rear door scuff plate.



11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. INSTALL REAR SEATBACK ASSEMBLY
for Bench Type Seatback:
for Separate Type Seatback LH Side:
for Separate Type Seatback RH Side:


13. INSTALL REAR SEAT CUSHION ASSEMBLY
for Bench Type Seatback:
for Separate Type Seatback:


14. INSTALL FRONT CENTER FLOOR COVER
  1. Engage the 2 guides to install the front center floor cover.

  1. Install the 3 clips.



15. INSTALL FRONT FLOOR COVER LH
  1. Engage the 3 guides.



    B301490E01
  1. Engage the 3 clips <B> to install the front floor cover LH.

  1. Install the 2 clips <A>.



16. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the 3 clips <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



17. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


18. INSTALL REAR SEAT HEADREST ASSEMBLY


19. PERFORM DIAGNOSTIC SYSTEM CHECK
(Click here)


20. INSPECT SRS WARNING LIGHT
(Click here)