Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3107-214    Lost Communication with Airbag System Control Module

for Preparation Click here


DESCRIPTION

  1. Refer to the description for DTC P3107-213 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3107
214
Open or short to +B in the communication circuit
(1 trip detection logic)
  1. Wire harness or connector
  2. Airbag sensor assembly
  3. Power management control ECU

Related Data List 
DTC No.
Data List
P3107-214
Collision Signal (Airbag)

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 .
Refer to the wiring diagram for DTC P3107-213 .

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (IG) and wait for 15 seconds or more.

1.CHECK DTC OUTPUT (SRS AIRBAG)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.

  1. Check if DTCs are output.

Result:
Result
Proceed to
Airbag system DTCs are not output.
A
Airbag system DTCs are output.
B

  1. Turn the ignition switch off.



B
GO TO DTC CHART (AIRBAG SYSTEM) (Click here)
A


2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)
  1. Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.

  1. Turn the ignition switch to ON (READY).



    A216762E10
  1. Measure the waveform.
    Item
    Contents
    Terminal
    G18-14 (GSW2) - G18-25 (E1)
    Equipment Setting
    5V/DIV., 500ms/DIV.
    Condition
    Ignition switch ON (READY)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B

    Text in Illustration  
    *a
    Component with harness connected
    (Airbag Sensor Assembly)

  1. Turn the ignition switch off.



B
Go to step 6
A


3.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the ignition switch off.


NEXT


4.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3107-214 is not output.
    A
    P3107-214 is output again.
    B

  1. Turn the ignition switch off.



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A


5.CHECK FOR INTERMITTENT PROBLEMS
(Click here)


NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A269501
  1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)


    A216765E06
  1. Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.
    Text in Illustration 
    *a
    Component with harness connected
    (Airbag Sensor Assembly)

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


8.CHECK HARNESS AND CONNECTOR (+B SHORT)


    A263605E01
  1. Remove the IGCT No. 2 fuse and AM2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly (w/ Smart Key System).
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    AM2 Fuse
    *3
    IGCT No. 2 Fuse



    A263606E01
  1. Remove the IGCT No. 2 fuse and ECU-B No. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly (w/o Smart Key System).
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    ECU-B No. 2 Fuse
    *3
    IGCT No. 2 Fuse



    A216763E18
  1. Disconnect connector G18 from the airbag sensor assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Airbag Sensor Assembly)



    A243895E21
  1. Measure the resistance according to the value(s) in the table below (w/ Smart Key System).

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - A38-2 (+B2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-1 (IG2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-2 (IG2D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-5 (+B1)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-6 (MREL)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-1 (AM22)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-14 (SPDI)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-1 (ACCD)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-2 (IG1D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-7 (AM21)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)



    A243895E22
  1. Measure the resistance according to the value(s) in the table below (w/o Smart Key System).

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - A38-2 (+B2)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-1 (IG2)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-5 (+B1)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-6 (MREL)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-1 (BATT)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-14 (SPDI)
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Connect the airbag sensor assembly connector.

  1. Install the IGCT No. 2 fuse and AM2 fuse (w/ Smart key System).

  1. Install the IGCT No. 2 fuse and ECU-B No. 2 fuse (w/o Smart key System).



NG
Go to step 11
OK


9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
  1. Disconnect connector G57 from the power management control ECU.

  1. Disconnect connector G18 from the airbag sensor assembly.



    A216764E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - G18-14 (GSW2)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) or G18-14 (GSW2) - Body ground and other terminals
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Rear view of wire harness connector
    (to Airbag Sensor Assembly)

    HINT:
    As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.

  1. Connect the airbag sensor assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK POWER MANAGEMENT CONTROL ECU


    A216763E18
  1. Disconnect connector G18 from the airbag sensor assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Airbag Sensor Assembly)

  1. Turn the ignition switch to ON (IG).



    A249168E13
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - Body ground
    Ignition switch ON (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

    NOTICE:
    Turning the ignition switch to ON (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Connect the airbag sensor assembly connector.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

11.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)


    A263605E01
  1. Remove the IGCT No. 2 fuse and AM2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly (w/ Smart Key System).
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    AM2 Fuse
    *3
    IGCT No. 2 Fuse



    A263606E01
  1. Remove the IGCT No. 2 fuse and ECU-B No. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly (w/o Smart Key System).
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    ECU-B No. 2 Fuse
    *3
    IGCT No. 2 Fuse



    A216763E18
  1. Disconnect connector G18 from the airbag sensor assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Airbag Sensor Assembly)

  1. Disconnect all the connectors from the power management control ECU.



    A238662E51
  1. Measure the resistance according to the value(s) in the table below (w/ Smart Key System).

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - A38-2 (+B2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-1 (IG2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-2 (IG2D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-5 (+B1)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-6 (MREL)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-1 (AM22)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-14 (SPDI)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-1 (ACCD)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-2 (IG1D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-7 (AM21)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



    A263607E04
  1. Measure the resistance according to the value(s) in the table below (w/o Smart Key System).

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - A38-2 (+B2)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-1 (IG2)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-5 (+B1)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-6 (MREL)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-1 (BATT)
    Ignition switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-14 (SPDI)
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the airbag sensor assembly connector.

  1. Connect the power management control ECU connectors.

  1. Install the IGCT No. 2 fuse and AM2 fuse (w/ Smart Key System).

  1. Install the IGCT No. 2 fuse and ECU-B No. 2 fuse (w/o Smart Key System).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)