Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0705-757    Transmission Range Sensor Circuit

for Preparation Click here


DESCRIPTION

The shift lever position sensor can send 7 different switch signals to the power management control ECU. The power management control ECU uses the signals to detect the shift lever position (P, R, N, D, or B). The power management control ECU also uses this information to determine intended direction of travel (forward or reverse).

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0705
757
Shift sensor circuit malfunction (abnormal pattern)
A malfunction in the P, R, N, D or B circuit is detected based on the shift sensor input pattern.
(1 trip detection logic)
  1. Wire harness or connector
  2. Shift lever position sensor
  3. Power management control ECU

Related Data List 
DTC No.
Data List
P0705-757
  1. Shift Sensor Shift Pos
  2. Shift Sensor SW-P
  3. Shift Sensor SW-R
  4. Shift Sensor SW-PR
  5. Shift Sensor SW-N
  6. Shift Sensor SW-DB1
  7. Shift Sensor SW-DB2
  8. Shift Sensor SW-PNB

WIRING DIAGRAM


A264043E02


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (IG).
  2. Slowly move the shift lever from P to B then back to P.

1.READ VALUE USING TECHSTREAM (SHIFT POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor SW - P, Shift Sensor SW - R, Shift Sensor SW - N, Shift Sensor SW - DB1, Shift Sensor SW - DB2, Shift Sensor SW - PR, Shift Sensor SW - PNB.

  1. While slowly moving the shift lever from P to B, then back to P, read the Data List (shift position) displayed on the Techstream.

    HINT:
    Be sure to move the shift lever slowly.


    Result:

    ECU Data List
    Shift Position
    P
    R
    N
    D
    B
    Shift Sensor SW-P
    ON
    OFF
    OFF
    OFF
    OFF
    Shift Sensor SW-R
    OFF
    ON
    OFF
    OFF
    OFF
    Shift Sensor SW-PR
    ON
    ON
    OFF
    OFF
    OFF
    Shift Sensor SW-N
    OFF
    OFF
    ON
    OFF
    OFF
    Shift Sensor SW-DB1
    OFF
    OFF
    OFF
    ON
    ON
    Shift Sensor SW-DB2
    OFF
    OFF
    OFF
    ON
    ON
    Shift Sensor SW-PNB
    ON
    OFF
    ON
    OFF
    ON

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    OK:
    DTC P0705-757 is not output.

  1. Turn the ignition switch off.



NG
Go to step 3
OK


2.CHECK FOR INTERMITTENT PROBLEMS
(Click here)


NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

3.CHECK SHIFT LEVER POSITION SENSOR
  1. Turn the ignition switch to ON (IG).



    A259789E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A39-15 (P) - Body ground
    Ignition switch ON (IG)
    Shift lever in P
    11 to 14 V
    A39-15 (P) - Body ground
    Ignition switch ON (IG)
    Any position except shift lever in P
    0 to 1.5 V
    A39-14 (R) - Body ground
    Ignition switch ON (IG)
    Shift lever in R
    11 to 14 V
    A39-14 (R) - Body ground
    Ignition switch ON (IG)
    Any position except shift lever in R
    0 to 1.5 V
    A39-9 (PR) - Body ground
    Ignition switch ON (IG)
    Shift lever in P or R
    11 to 14 V
    A39-9 (PR) - Body ground
    Ignition switch ON (IG)
    Any position except shift lever in P and R
    0 to 1.5 V
    A39-8 (N) - Body ground
    Ignition switch ON (IG)
    Shift lever in N
    11 to 14 V
    A39-8 (N) - Body ground
    Ignition switch ON (IG)
    Any position except shift lever in N
    0 to 1.5 V
    A39-11 (DB1) - Body ground
    Ignition switch ON (IG)
    Shift lever in D or B
    11 to 14 V
    A39-11 (DB1) - Body ground
    Ignition switch ON (IG)
    Any position except shift lever in D and B
    0 to 1.5 V
    A39-13 (DB2) - Body ground
    Ignition switch ON (IG)
    Shift lever in D or B
    11 to 14 V
    A39-13 (DB2) - Body ground
    Ignition switch ON (IG)
    Any position except shift lever in D and B
    0 to 1.5 V
    A39-16 (PNB) - Body ground
    Ignition switch ON (IG)
    Shift lever in P, N or B
    11 to 14 V
    A39-16 (PNB) - Body ground
    Ignition switch ON (IG)
    Any position except shift lever in P, N and B
    0 to 1.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Turn the ignition switch off.



NG
Go to step 4
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the shift lever position sensor connector.

  1. Turn the ignition switch to ON (IG).



    A210242E12
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C23-7 (+B) - Body ground
    Ignition switch ON (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Shift Lever Position Sensor)

    NOTICE:
    Turning the ignition switch to ON (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Connect the shift lever position sensor connector.



NG
REPAIR OR REPLACE POWER SOURCE CIRCUIT
OK


5.INSPECT SHIFT LEVER POSITION SENSOR
  1. Disconnect the shift lever position sensor connector.



    A264044E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C23-7 (+B) - C23-3 (PR)
    Shift lever in P
    Below 1 Ω
    C23-7 (+B) - C23-4 (PNB)
    Below 1 Ω
    C23-7 (+B) - C23-8 (P)
    Below 1 Ω
    C23-7 (+B) - C23-1 (DB1), C23-2 (N), C23-6 (DB2) and C23-9 (R)
    10 kΩ or higher
    C23-7 (+B) - C23-3 (PR)
    Shift lever in R
    Below 1 Ω
    C23-7 (+B) - C23-9 (R)
    Below 1 Ω
    C23-7 (+B) - C23-1 (DB1), C23-2 (N), C23-4 (PNB), C23-6 (DB2) and C23-8 (P)
    10 kΩ or higher
    C23-7 (+B) - C23-2 (N)
    Shift lever in N
    Below 1 Ω
    C23-7 (+B) - C23-4 (PNB)
    Below 1 Ω
    C23-7 (+B) - C23-1 (DB1), C23-3 (PR), C23-6 (DB2), C23-8 (P) and C23-9 (R)
    10 kΩ or higher
    C23-7 (+B) - C23-1 (DB1)
    Shift lever in D
    Below 1 Ω
    C23-7 (+B) - C23-6 (DB2)
    Below 1 Ω
    C23-7 (+B) - C23-2 (N), C23-3 (PR), C23-4 (PNB), C23-8 (P) and C23-9 (R)
    10 kΩ or higher
    C23-7 (+B) - C23-1 (DB1)
    Shift lever in B
    Below 1 Ω
    C23-7 (+B) - C23-4 (PNB)
    Below 1 Ω
    C23-7 (+B) - C23-6 (DB2)
    Below 1 Ω
    C23-7 (+B) - C23-2 (N), C23-3 (PR), C23-8 (P) and C23-9 (R)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Shift Lever Position Sensor)

    HINT:
    Terminal No. 5 on the component side connector is empty.

  1. Connect the shift lever position sensor connector.



NG
REPLACE SHIFT LEVER POSITION SENSOR (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR