Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A1A-151    Generator Control Module

DTC    P0A1A-155    Generator Control Module

DTC    P0A1A-156    Generator Control Module

DTC    P0A1A-658    Generator Control Module

DTC    P0A1A-659    Generator Control Module

DTC    P0A1A-791    Generator Control Module

for Preparation Click here


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions. If any of the following DTCs are output, replace the inverter with converter assembly.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A1A
151
MG ECU internal malfunction
Run pulse signal cycle deviation or stop
(1 trip detection logic)
Inverter with converter assembly
155
MG ECU internal malfunction
A/D converter malfunction
(1 trip detection logic)
156
MG ECU internal malfunction
CPU ROM-RAM error
(1 trip detection logic)
658
MG ECU internal malfunction
Calculation check error
(1 trip detection logic)
659
MG ECU internal malfunction
Communication error (from generator (MG1) to motor (MG2))
(1 trip detection logic)
791
MG ECU internal malfunction
R/D converter communication error
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P0A1A-791
Generator (MG1) Rev
P0A1A-151
P0A1A-155
P0A1A-156
P0A1A-658
P0A1A-659
-

MONITOR DESCRIPTION

The MG ECU performs many diagnostic tests to verify proper operation of internal ECU systems. In one of those tests, the MG ECU checks the result of the generator CPU self-test. If the MG ECU detects a "Fail" from the generator CPU self-test, it will conclude that there is an internal malfunction in the generator CPU. The power management control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A1A (INF 151): RUN pulse malfunction
P0A1A (INF 155): A/D malfunction (1 MG CPU)
P0A1A (INF 156): RAM and ROM destruction
P0A1A (INF 658): MG CPU ALU malfunction
P0A1A (INF 659): MG CPU communication malfunction (1 MG CPU to 2 MG CPU)
P0A1A (INF 791): R/D converter communication malfunction
Required sensors / components
Inverter with converter assembly (MG ECU)
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU
DTC P0A1A (INF 151/155/156/658/659/791) is not detected

CONFIRMATION DRIVING PATTERN


A218446E11

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (READY) and after 1 minute or more, turn the ignition switch off. [A]
  6. Repeat [A] 3 times. [B]
  7. Turn the ignition switch to ON (IG) and turn the Techstream on.
  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]
  9. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output, perform the following procedure.

  10. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  11. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

INSPECTION PROCEDURE

HINT:
  1. If DTC P0A1A-151, P0A1A-155, P0A1A-658, P0A1A-659 or P0A1A-791 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the ignition switch to ON (IG) and wait for 5 seconds or more.
  2. If DTC P0A1A-156 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the ignition switch to ON (IG) and wait for 1 minute or more.

1.REPLACE INVERTER WITH CONVERTER ASSEMBLY
(Click here)

NEXT

COMPLETED