Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A38-257    Generator Temperature Sensor Circuit Low

DTC    P0A39-259    Generator Temperature Sensor Circuit High

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0A37-260 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A38
257
Short to GND or short in the generator temperature sensor circuit
(1 trip detection logic)
  1. Wire harness or connector
  2. Power management control ECU
  3. Hybrid vehicle transaxle assembly (Generator temperature sensor)
P0A39
259
Open or short to +B in the generator temperature sensor circuit
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P0A38-257
Motor Temp No2
P0A39-259

HINT:
After confirming that DTC P0A38-257 or P0A39-259 is output, use the Techstream to check "Motor Temp No2" in the power management control ECU Data List.


Displayed Temperature
Malfunction
-40°C (-40°F)
Open circuit or short to +B
215°C (419°F)
Short circuit or short to GND

WIRING DIAGRAM


C280811E04


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (IG) and wait for 5 seconds or more.

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A269501
  1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


2.READ VALUE USING TECHSTREAM (MOTOR TEMP NO2)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.

  1. Read the Data List.

    Result:
    Result
    Proceed to
    -40°C (-40°F)
    A
    215°C (419°F)
    B
    Same as actual temperature
    C

  1. Turn the ignition switch off.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3.READ VALUE USING TECHSTREAM (CHECK FOR OPEN)


    A267571
  1. Disconnect the generator temperature sensor connector.



    A217045E07
  1. Connect terminals 4 (GMT) and 8 (GMTG) of vehicle side connector C24 of the generator temperature sensor.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Motor Temp No2
    Terminals GMT and GMTG connected.
    Ignition switch ON (IG)
    215°C (419°F)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Generator Temperature Sensor)

    HINT:
    The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.

  1. Turn the ignition switch off.

  1. Connect the generator temperature sensor connector.



NG
Go to step 4
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - GENERATOR TEMPERATURE SENSOR)


    A249277E26
  1. Connect terminals 26 (GMT) and 27 (GMTG) of connector A38 of the power management control ECU.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Motor Temp No2
    Terminals GMT and GMTG connected.
    Ignition switch ON (IG)
    215°C (419°F)

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Turn the ignition switch off.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.READ VALUE USING TECHSTREAM (CHECK FOR SHORT)


    A267571
  1. Disconnect the generator temperature sensor connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.

  1. Read the Data List.

    OK:
    Tester Display
    Condition
    Specified Condition
    Motor Temp No2
    Ignition switch ON (IG)
    -40°C (-40°F)

    HINT:
    The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.

  1. Turn the ignition switch off.

  1. Connect the generator temperature sensor connector.



NG
Go to step 6
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)  

6.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the generator temperature sensor connector.

  1. Disconnect connector A38 from the power management control ECU.



    A217254E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C24-4 (GMT) - A38-26 (GMT)
    Ignition switch off
    Below 1 Ω
    C24-8 (GMTG) - A38-27 (GMTG)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C24-4 (GMT) or A38-26 (GMT) - Body ground and other terminals
    Ignition switch off
    10 kΩ or higher
    C24-8 (GMTG) or A38-27 (GMTG) - Body ground and other terminals
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Generator Temperature Sensor)
    *b
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the power management control ECU connector.

  1. Connect the generator temperature sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)