Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A4B-253    Generator Position Sensor Circuit

DTC    P0A4C-513    Generator Position Sensor Circuit Range / Performance

DTC    P0A4D-255    Generator Position Sensor Circuit Low

for Preparation Click here


DESCRIPTION

A resolver is a sensor that is used to detect the position of the magnetic poles of the rotor in motor generator. Knowing the position of the poles is indispensable for ensuring precise control of motor (MG2) and generator (MG1).
Each resolver contains a stator that has an excitation coil and 2 detection coils (S, C). The gap between the stator and rotor changes as the rotor turns because the rotor is oval shaped. An alternating current with a predetermined frequency flows through the excitation coil, and detection coils S and C output alternating currents in accordance with the sensor rotor position.
The MG ECU located in the inverter with converter assembly detects the absolute position of the rotor according to the phases of detection coils S and C and the heights of their waveforms. Furthermore, the CPU calculates the amount of change in the position within a predetermined length of time, in order to use the resolver as a speed sensor.
The MG ECU monitors signals output from the generator resolver and detects malfunctions.

A221242E01


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A4B
253
Interphase short in the generator resolver circuit.
Short circuit between signal lines of generator resolver phases is electrically detected.
(1 trip detection logic)
  1. Inverter with converter assembly
  2. Hybrid vehicle transaxle assembly
  3. Wire harness or connector
P0A4C
513
Generator resolver output signal is out of the normal range (amplitude is too large or too small).
(1 trip detection logic)
P0A4D
255
Open or short in the generator resolver circuit.
Generator resolver signal is out of the normal range (signal output amplitude is extremely small).
(1 trip detection logic)

MONITOR DESCRIPTION

The MG ECU monitors the generator resolver output signal. If the MG ECU detects output signals that are out of the normal range or specification, it will conclude that there is a malfunction of the generator resolver. If a malfunction is detected, the power management control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A4B (INF 253): Short circuit between phases
P0A4C (INF 513): Range check
P0A4D (INF 255): Circuit discontinuity / short circuit
Required sensors / components
Generator resolver
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Generator resolver
DTC P0A4B (INF 253) is not detected
DTC P0A4C (INF 513) is not detected
DTC P0A4D (INF 255) is not detected

CONFIRMATION DRIVING PATTERN


A278265E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off.
  5. Turn the ignition switch to ON (READY) and turn the Techstream on.
  6. With the vehicle stopped and shift lever in P, wait for 10 seconds. [A]
  7. With the vehicle stopped and shift lever in P, accelerate from 0 to 100 % for 10 seconds. [B]
  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
  9. Check that permanent DTCs are cleared.
  10. If the permanent DTCs are not cleared, perform a universal trip, and then check for permanent DTCs again.

HINT:
  1. If a permanent DTC is output, the system is malfunctioning.
  2. If no permanent DTC is output, the system is normal.


CONFIRMATION DRIVING PATTERN


A308309E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (IG) and wait for 5 seconds or more.
  6. Turn the ignition switch to ON (READY) with the shift lever in P and wait for 5 seconds or more.
  7. Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.
  8. Keep the engine running for 5 seconds or more.
  9. Drive the vehicle forward with the shift lever in D for 5 m or more. [A]
  10. Drive the vehicle backward with the shift lever in R for 5 m or more. [B]
  11. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]
  12. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output, perform the following procedure.

  13. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  14. If the permanent DTCs are not cleared, perform a universal trip, and then check for permanent DTCs again.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A1A-200 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  2. Check for output DTCs again after the repair has been completed. If P0A78-286 or P0A7A-324 is output, replace the inverter with converter assembly.

HINT:
  1. If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.
  2. If the resolver is malfunctioning, the vehicle may not drive smoothly.
  3. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Turn the ignition switch to ON (IG) and wait for 5 seconds or more.
    2. Turn the ignition switch to ON (READY) with the shift lever in P and wait for 5 seconds or more.
    3. Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.
    4. Keep the engine running for 5 seconds or more.
    5. Drive the vehicle forward with the shift lever in D for 5 m or more.
    6. Drive the vehicle backward with the shift lever in R for 5 m or more.

1.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



    A267460
  1. Check the connector connections and contact pressure of the low voltage connectors of the inverter with converter assembly (Click here).

    NOTICE:
    Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

    OK:
    The connectors are connected securely and there are no contact pressure problems.

    HINT:
    When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.



NG
CONNECT SECURELY
OK


2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).



    A217747E15
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-12 (GRFG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-7 (GSN) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-8 (GSNG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-10 (GCS) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-9 (GCSG) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

    NOTICE:
    Turning the ignition switch to ON (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK GENERATOR RESOLVER

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A217747E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) - C28-12 (GRFG)
    Ignition switch off
    7.1 to 21.6 Ω
    C28-7 (GSN) - C28-8 (GSNG)
    Ignition switch off
    13.7 to 34.5 Ω
    C28-10 (GCS) - C28-9 (GCSG)
    Ignition switch off
    12.8 to 32.4 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) or C28-12 (GRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-7 (GSN) or C28-8 (GSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-10 (GCS) or C28-9 (GCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

  1. Connect the inverter with converter assembly connector.



NG
Go to step 8
OK


4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the ignition switch to ON (IG).



    A217747E16
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-2 (MRFG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-3 (MSN) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-4 (MSNG) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-6 (MCS) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C28-5 (MCSG) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

    NOTICE:
    Turning the ignition switch to ON (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK MOTOR RESOLVER

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A217747E16
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) - C28-2 (MRFG)
    Ignition switch off
    7.1 to 21.6 Ω
    C28-3 (MSN) - C28-4 (MSNG)
    Ignition switch off
    13.7 to 34.5 Ω
    C28-6 (MCS) - C28-5 (MCSG)
    Ignition switch off
    12.8 to 32.4 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) or C28-2 (MRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-3 (MSN) or C28-4 (MSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-6 (MCS) or C28-5 (MCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)

  1. Connect the inverter with converter assembly connector.



NG
Go to step 10
OK


6.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)


    A267571
  1. Check the connection of the generator resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


7.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)


    A267572
  1. Check the connection of the motor resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

8.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)


    A267571
  1. Check the connection of the generator resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


9.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A268860E02
  1. Disconnect the generator resolver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) - C24-1 (GRF)
    Ignition switch off
    Below 1 Ω
    C28-12 (GRFG) - C24-5 (GRFG)
    Ignition switch off
    Below 1 Ω
    C28-7 (GSN) - C24-2 (GSN)
    Ignition switch off
    Below 1 Ω
    C28-8 (GSNG) - C24-6 (GSNG)
    Ignition switch off
    Below 1 Ω
    C28-10 (GCS) - C24-3 (GCS)
    Ignition switch off
    Below 1 Ω
    C28-9 (GCSG) - C24-7 (GCSG)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-11 (GRF) or C24-1 (GRF) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-12 (GRFG) or C24-5 (GRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-7 (GSN) or C24-2 (GSN) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-8 (GSNG) or C24-6 (GSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-10 (GCS) or C24-3 (GCS) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-9 (GCSG) or C24-7 (GCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Front view of wire harness connector
    (to Generator Resolver)

    HINT:
    The generator resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.

  1. Connect the generator resolver connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)  

10.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)


    A267572
  1. Check the connection of the motor resolver connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector C28 from the inverter with converter assembly.



    A268861E02
  1. Disconnect the motor resolver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) - C26-3 (MRF)
    Ignition switch off
    Below 1 Ω
    C28-2 (MRFG) - C26-6 (MRFG)
    Ignition switch off
    Below 1 Ω
    C28-3 (MSN) - C26-1 (MSN)
    Ignition switch off
    Below 1 Ω
    C28-4 (MSNG) - C26-4 (MSNG)
    Ignition switch off
    Below 1 Ω
    C28-6 (MCS) - C26-2 (MCS)
    Ignition switch off
    Below 1 Ω
    C28-5 (MCSG) - C26-5 (MCSG)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    C28-1 (MRF) or C26-3 (MRF) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-2 (MRFG) or C26-6 (MRFG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-3 (MSN) or C26-1 (MSN) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-4 (MSNG) or C26-4 (MSNG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-6 (MCS) or C26-2 (MCS) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher
    C28-5 (MCSG) or C26-5 (MCSG) - Body ground and other terminals
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Front view of wire harness connector
    (to Motor Resolver)

    HINT:
    The motor resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.

  1. Connect the motor resolver connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)