Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A78-266    Drive Motor "A" Inverter Performance

DTC    P0A78-267    Drive Motor "A" Inverter Performance

for Preparation Click here


DESCRIPTION

The inverter contains a three-phase bridge circuit, which consists of six power transistors (IGBTs) each for MG1 and MG2. The inverter converts high-voltage direct current from the HV battery into three-phase alternating current for generator (MG1) and motor (MG2); it also converts three-phase alternating current supplied by generator (MG1) and motor (MG2) into direct current for the HV battery. The MG ECU controls the actuation of the power transistors (IGBTs). The inverter transmits information necessary for control, such as amperage and voltage, to the MG ECU.

HINT:
The term "drive motor A" indicates motor (MG2).


C280822E02

The MG ECU uses an inverter voltage sensor, which is built into the inverter, to detect boosted high voltage to allow control of the voltage boost.
The inverter voltage sensor outputs voltage that fluctuates between 0 to 5 V according to changes in VH.
The MG ECU monitors the inverter voltage sensor and detects the following malfunctions.
The MG ECU monitors the inverter voltage sensor and detects the following malfunctions.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A78
266
Inverter voltage (VH) signal is stuck low
Stores a DTC when the VH sensor signal is excessively low.
(1 trip detection logic)
Inverter with converter assembly
267
Inverter voltage (VH) signal is stuck high
Stores a DTC when the VH sensor signal is excessively high.
(1 trip detection logic)

Related Data List 
DTC No.
Data List
P0A78-266
VH-Voltage after Boosting
P0A78-267

MONITOR DESCRIPTION

The MG ECU monitors the inverter voltage (VH) sensor circuit. If the MG ECU detects an open or short in the VH sensor circuit, the power management control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A78 (INF 266): VH malfunction (GND short malfunction)
P0A78 (INF 267): VH malfunction (+B short and disconnection malfunction)
Required sensors / components
Motor inverter
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU
DTC P0A78 (INF 266/267) is not detected

CONFIRMATION DRIVING PATTERN


A218446E14

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (READY) and after a 5 seconds, turn the ignition switch off. [A]
  6. Repeat [A] 3 times. [B]
  7. Turn the ignition switch to ON (IG) and turn the Techstream on.
  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]
  9. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  10. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  11. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (READY) and wait for 5 seconds or more.

1.REPLACE INVERTER WITH CONVERTER ASSEMBLY
(Click here)

HINT:
The signal line from the inverter voltage (VH) sensor is connected to the MG ECU inside the inverter with converter assembly. If P0A78-266 or P0A78-267 is output, replace the inverter with converter assembly.


NEXT

COMPLETED