Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A94-589    DC / DC Converter Performance

for Preparation Click here


DESCRIPTION

The MG ECU uses a voltage sensor that is built into the boost converter to detect pre-boost high voltage (VL) to allow boost control. The MG ECU monitors the boost converter voltage sensor signal line and detects the following malfunctions.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A94
589
Boost converter voltage (VL) signal is stuck (Low)
(1 trip detection logic)
Inverter with converter assembly

Related Data List 
DTC No.
Data List
P0A94-589
VL-Voltage before Boosting

MONITOR DESCRIPTION

The MG ECU monitors the boost converter voltage (VL) sensor circuit. If the MG ECU detects an open or short circuit malfunction of the VL sensor circuit, the power management control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A94 (INF 589): VL malfunction (GND short)
Required sensors / components
Boost converter
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Power management control ECU
DTC P0A94 (INF 589) is not detected

CONFIRMATION DRIVING PATTERN


A218446E15

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 30 seconds or more.
  5. Turn the ignition switch to ON (IG) and after 5 seconds, turn the ignition switch off. [A]
  6. Repeat [A] 3 times. [B]
  7. Turn the ignition switch to ON (IG) and turn the Techstream on.
  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]
  9. Read the current DTCs.

    HINT:
    1. If a current DTC is output, the system is malfunctioning.
    2. If a current DTC is not output and want to confirm permanent DTC, perform the following procedure.

  10. Check that permanent DTCs are cleared. If no permanent DTC is output, the system is normal.
  11. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch to ON (IG) and wait for 5 seconds or more.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only P0A94-589 is output or P0A94-589 and DTCs other than the ones in the table below are also output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0ADC-226
    Hybrid Battery Positive Contactor Control Circuit High
    P0AE0-228
    Hybrid Battery Negative Contactor Control Circuit High

    HINT:
    P0A94-589 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the ignition switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)