Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1247/47    Stroke Sensor Malfunction

DTC    C1346/71    Stroke Sensor Zero Point Learning Malfunction (Test Mode DTC)

DTC    C1392/48    Stroke Sensor Zero Point Calibration Undone

for Preparation Click here


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU.
DTC C1346/71 will be cleared when the brake pedal stroke sensor assembly sends a brake pedal stroke sensor assembly signal or when Test Mode ends. DTC C1346/71 is output only in Test Mode.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
C1247/47
211
Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more.
  1. Open or short in brake pedal stroke sensor assembly power supply circuit
  2. Improperly connected connector, deformation or corrosion of terminals
  3. Skid control ECU (Brake booster with master cylinder assembly)
↑
212
Sensor output voltage 1 (SKS1) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.
  1. Open or short in wire harness
  2. Improperly connected connector, deformation or corrosion of terminals
  3. Brake pedal stroke sensor assembly
↑
213
Sensor output voltage 2 (SKS2) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCSK) for 0.2 seconds or more.
↑
↑
214
Either of the following is detected:
  1. Fluctuation of sensor output 1 (SKS1) is out of specification.
  2. The difference between the present value and last value of sensor output voltage 1 (SKS1) is 8.5% or more (0.43 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.
↑
↑
215
Either of the following is detected:
  1. Fluctuation of sensor output 2 (SKS2) is out of specification.
  2. The difference between the present value and last value of the sensor output voltage 2 (SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) for 0.2 seconds or more.
↑
↑
218
An excessive difference between the change in sensor output 1 (SKS1) and sensor output 2 (SKS2) is detected for 0.2 seconds or more.
↑
↑
219
Sensor data is invalid for 0.2 seconds or more.
(Skid control ECU internal monitor circuit malfunction.)
↑
↑
223
Sensor data is invalid for 0.2 seconds or more.
(Open, short, or noise.)
↑
C1392/48
-
Zero point calibration of brake pedal stroke sensor assembly is unfinished.
  1. Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete)
  2. Skid control ECU (Brake booster with master cylinder assembly)
C1346/71
-
Detected only during Test Mode.
  1. Brake pedal stroke sensor assembly
  2. Brake pedal stroke sensor assembly circuit

WIRING DIAGRAM


C235540E12


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).

1.CHECK BRAKE PEDAL
  1. Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.

  1. Check and adjust the brake pedal height .

  1. Adjust the brake pedal stroke sensor assembly .


NEXT


2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector and the brake pedal stroke sensor assembly connector.

  1. Check both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-39 (VCSK) - A42-3 (VCSK)
    Always
    Below 1 Ω
    A41-39 (VCSK) - Body ground
    Always
    10 kΩ or higher
    A41-41 (SKG) - A42-1 (SKG)
    Always
    Below 1 Ω
    A41-41 (SKG) - Body ground
    Always
    10 kΩ or higher
    A41-42 (SKS) - A42-4 (SKS1)
    Always
    Below 1 Ω
    A41-42 (SKS) - Body ground
    Always
    10 kΩ or higher
    A41-40 (SKS2) - A42-2 (SKS2)
    Always
    Below 1 Ω
    A41-40 (SKS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)


    C234579E07
  1. Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A42-3 (VCSK) - A42-1 (SKG)
    Ignition switch ON (IG)
    4.84 to 5.16 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Pedal Stroke Sensor Assembly)



NG
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)
OK

REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY (Click here)