DTC P3004-800 High Voltage Power Resource |
DTC P3004-801 High Voltage Power Resource |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P3004 | 800 | High-voltage circuit malfunctions between the HV battery and inverter with converter assembly. Excessive overcurrent occurs during precharge (time from when SMRP turns on until SMRG turns on). (1 trip detection logic) |
|
| 801 | High-voltage circuit malfunctions between the HV battery and inverter with converter assembly. Minimal overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on). (1 trip detection logic) |
| DTC No. | Data List |
| P3004-800 |
|
| P3004-801 |
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| Only P3004-800 or P3004-801 is output, or DTCs other than the ones in the table below are also output. | A |
| DTCs shown in Table 1 are output simultaneously. | B |
| DTCs shown in Table 2 are output simultaneously. | C |
| DTC No. | Relevant Diagnosis |
| P0A09-265 | DC/DC Converter Status Circuit Low Input |
| P0A10-263 | DC/DC Converter Status Circuit High Input |
| DTC No. | Relevant Diagnosis |
| P0ABF-123 | Hybrid Battery Pack Current Sensor Circuit |
| P0AC0-123 | Hybrid Battery Pack Current Sensor Circuit Range / Performance |
| P0AC1-123 | Hybrid Battery Pack Current Sensor Circuit Low |
| P0AC2-123 | Hybrid Battery Pack Current Sensor Circuit High |
| P0AFC-123 | Hybrid Battery Pack Sensor Module |
| P0B3D-123 | Hybrid Battery Voltage Sensor "A" Circuit Low |
| P0B42-123 | Hybrid Battery Voltage Sensor "B" Circuit Low |
| P0B47-123 | Hybrid Battery Voltage Sensor "C" Circuit Low |
| P0B4C-123 | Hybrid Battery Voltage Sensor "D" Circuit Low |
| P0B51-123 | Hybrid Battery Voltage Sensor "E" Circuit Low |
| P0B56-123 | Hybrid Battery Voltage Sensor "F" Circuit Low |
| P0B5B-123 | Hybrid Battery Voltage Sensor "G" Circuit Low |
| P0B60-123 | Hybrid Battery Voltage Sensor "H" Circuit Low |
| P0B65-123 | Hybrid Battery Voltage Sensor "I" Circuit Low |
| P0B6A-123 | Hybrid Battery Voltage Sensor "J" Circuit Low |
| P0B6F-123 | Hybrid Battery Voltage Sensor "K" Circuit Low |
| P308A-123 | Hybrid Battery Voltage Sensor All Circuits Low |
| U029A-123 | Lost Communication with Hybrid Battery Pack Sensor Module |
Turn the ignition switch off.
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR) |
![]() |
Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).
|
| ||||
| OK | |
| 3.CHECK COMPRESSOR WITH MOTOR ASSEMBLY |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Remove the inverter cover from the inverter with converter assembly.
![]() |
Disconnect connector D2 of the No. 2 engine wire (air conditioning harness) from the inverter with converter assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Tester Probe Polarity) | Switch Condition | Specified Condition |
| D2-2 (ACPE) (Negative probe) - D2-1 (ACPB) (Positive probe) | Ignition switch off | 100 kΩ or higher |
| *a | No. 2 Engine Wire (Air Conditioning Harness) (Inverter with Converter Assembly Side) |
Connect the No. 2 engine wire (air conditioning harness) to the inverter with converter assembly.
Install the inverter cover.
Install the inverter terminal cover.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY) |
Check that the service plug grip is not installed.
Disconnect connector A38 from power management control ECU.
Disconnect connector A47 from the inverter with converter assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A47-12 (NODD) - A38-21 (NODD) | Ignition switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| A47-12 (NODD) or A38-21 (NODD) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
| *b | Front view of wire harness connector (to Inverter with Converter Assembly) |
Connect the inverter with converter assembly connector.
Connect the power management control ECU connector.
|
| ||||
| OK | |
| 5.CHECK POWER MANAGEMENT CONTROL ECU |
Check that the service plug grip is not installed.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A38-21(NODD) - G57-6(E1) | Ignition switch ON (IG) | Less than 1.5 V |
| *a | Component with harness connected (Power Management Control ECU) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
|
| ||||
| OK | |
| 6.CHECK FRAME WIRE |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Remove the inverter cover from the inverter with converter assembly.
![]() |
Disconnect connector P1 of the frame wire from the inverter with converter assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P1-2 (CBI) - P1-1 (CEI) | Ignition switch off | 10 kΩ or higher |
| *a | Frame Wire (Inverter With Converter Assembly Side) |
Connect the frame wire.
Install the inverter cover.
Install the inverter terminal cover.
|
| ||||
| OK | ||
| ||
| 7.CHECK NO. 2 ENGINE WIRE |
Check that the service plug grip is not installed.
![]() |
Remove the inverter terminal cover from the inverter with converter assembly.
![]() |
Remove the inverter cover from the inverter with converter assembly.
![]() |
Disconnect connector D2 of the No. 2 engine wire (air conditioning harness) from the inverter with converter assembly.
![]() |
Disconnect connector D1 of the No. 2 engine wire (air conditioning harness) from the compressor with motor assembly .
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D2-1 (ACPB) - D2-2 (ACPE) | Ignition switch off | 10 kΩ or higher |
| *a | No. 2 Engine Eire (Air Conditioning Harness) (Inverter with Converter Assembly Side) |
Connect the No. 2 engine wire (air conditioning harness) to the compressor with motor assembly.
Connect the No. 2 engine wire (air conditioning harness) to the inverter with converter assembly.
Install the inverter cover.
Install the inverter terminal cover.
|
| ||||
| OK | ||
| ||
| 8.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid vehicle battery cover panel LH .
![]() |
Disconnect connector P5 and connector P4 of the frame wire from the hybrid battery junction block assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P4-1 (CEI) - P5-1 (CBI) | Ignition switch off | 10 kΩ or higher |
Connect the frame wire.
Install the No. 1 hybrid vehicle battery cover panel LH.
|
| ||||
| OK | ||
| ||