POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH |

| 1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR) - AUXILIARY BATTERY) |
Disconnect the L1 power window regulator switch assembly (for rear LH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L1-3 (B) - Body ground | Ignition switch ON (IG) | 11 to 14 V |
|
| ||||
| OK | |
| 2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR LH DOOR) |
![]() |
Remove the power window regulator switch assembly (for rear LH door) (Click here).
Measure the resistance when the switch is operated according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (D) - 2 (SD) | UP | Below 1 Ω |
| 3 (B) - 4 (U) | Below 1 Ω | |
| 1 (D) - 2 (SD) | off | Below 1 Ω |
| 4 (U) - 5 (SU) | Below 1 Ω | |
| 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
| 1 (D) - 3 (B) | Below 1 Ω |
| *a | Component without harness connected (Power Window Regulator Switch Assembly (for Rear LH Door)) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR) - POWER WINDOW REGULATOR MOTOR LH) |
Disconnect the L2 power window regulator motor assembly LH (for rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L1-4 (U) - L2-1 (U) | Always | Below 1 Ω |
| L1-1 (D) - L2-2 (D) | Always | Below 1 Ω |
| L1-4 (U) - Body ground | Always | 10 kΩ or higher |
| L1-1 (D) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
![]() |
Remove the power window regulator master switch assembly (Click here).
Measure the resistance when the switch is operated according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 6 (B) - 12 (U) | UP | Below 1 Ω |
| 1 (E) - 13 (D) | Below 1 Ω | |
| 1 (E) - 12 (U) | off | Below 1 Ω |
| 1 (E) - 13 (D) | Below 1 Ω | |
| 6 (B) - 13 (D) | DOWN | Below 1 Ω |
| 1 (E) - 12 (U) | Below 1 Ω |
| *a | Component without harness connected (Power Window Regulator Master Switch Assembly) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR SWITCH (FOR REAR LH DOOR)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J1-12 (U) - L1-5 (SU) | Always | Below 1 Ω |
| J1-13 (D) - L1-2 (SD) | Always | Below 1 Ω |
| J1-12 (U) - Body ground | Always | 10 kΩ or higher |
| J1-13 (D) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||