Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / D-Door Motor or Main Body / Data List.

  5. Read the Data List according to the display on the Techstream.

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / ON or OFF
    ON: Driver door power window auto switch operated
    OFF: Driver door power window auto switch not operated
    -
    D Door P/W Up SW
    Driver door power window manual up switch signal / ON or OFF
    ON: Driver door power window manual up switch operated
    OFF: Driver door power window manual up switch not operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / ON or OFF
    ON: Driver door power window manual down switch operated
    OFF: Driver door power window manual down switch not operated
    -
    Glass Position (Close - 1/4)
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (1/4 - 2/4)
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (2/4 - 3/4)
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (3/4 - Open)
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs will be displayed
    -

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Courtesy SW
    Front door courtesy light switch RH / ON or OFF
    OFF: Front door RH closed
    ON: Front door RH open
    -
    FL Door Courtesy SW
    Front door courtesy light switch LH / ON or OFF
    OFF: Front door LH closed
    ON: Front door LH open
    -
    Communication D-Door Motor
    Connection status between power window regulator motor assembly LH (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / D-Door Motor or Main Body / Active Test.

  5. Perform the Active Test according to the display on the Techstream.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    D-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    IG OFF P/W Control Permission Output
    Power window
    OFF / ON
    Perform this Active Test with the ignition switch off