AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Speaker Circuit |

| 1.CHECK HARNESS AND CONNECTOR |
Disconnect the connectors from the radio and display receiver assembly and speakers.
Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| G76-1 (FR+) - H9-3 (TWR+) | Always | Below 1 Ω |
| G76-5 (FR-) - H9-1 (TWR-) | Always | Below 1 Ω |
| G76-2 (FL+) - J9-3 (TWL+) | Always | Below 1 Ω |
| G76-6 (FL-) - J9-1 (TWL-) | Always | Below 1 Ω |
Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| H9-4 (+) - H8-1 | Always | Below 1 Ω |
| H9-2 (-) - H8-2 | Always | Below 1 Ω |
| J9-4 (+) - J8-1 | Always | Below 1 Ω |
| J9-2 (-) - J8-2 | Always | Below 1 Ω |
Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| G77-1 (RR+) - K4-1 | Always | Below 1 Ω |
| G77-3 (RR-) - K4-2 | Always | Below 1 Ω |
| G77-2 (RL+) - L4-1 | Always | Below 1 Ω |
| G77-6 (RL-) - L4-2 | Always | Below 1 Ω |
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| G76-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| G76-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| G76-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| G76-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| G77-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| G77-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| G77-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| G77-6 (RL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| H9-4 (+) - Body ground | Always | 10 kΩ or higher |
| H9-2 (-) - Body ground | Always | 10 kΩ or higher |
| J9-4 (+) - Body ground | Always | 10 kΩ or higher |
| J9-2 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Resistance check
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H8-1 - H8-2 | Always | 3.2 to 4.8 Ω |
| J8-1 - J8-2 | Always | 3.2 to 4.8 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Front No. 1 Speaker Assembly) |
|
| ||||
| OK | |
| 3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Resistance check
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H9-3 (TWR+) - H9-1 (TWR-) | Always | 10 kΩ or higher |
| H9-3 (TWR+) - H9-4 (+) | Always | Below 1 Ω |
| H9-2 (-) - H9-1 (TWR-) | Always | Below 1 Ω |
| J9-3 (TWL+) - J9-1 (TWL-) | Always | 10 kΩ or higher |
| J9-3 (TWL+) - J9-4 (+) | Always | Below 1 Ω |
| J9-2 (-) - J9-1 (TWL-) | Always | Below 1 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Front No. 2 Speaker Assembly) |
|
| ||||
| OK | |
| 4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
Check that the malfunction disappears when a known good speaker is installed (Click here).
|
| ||||
| OK | ||
| ||
| 5.INSPECT REAR SPEAKER ASSEMBLY |
Resistance check
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K4-1 - K4-2 | Always | 3.2 to 4.8 Ω |
| L4-1 - L4-2 | Always | 3.2 to 4.8 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Rear Speaker Assembly) |
|
| ||||
| OK | ||
| ||