Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



OUTLINE OF COMBINATION METER ASSEMBLY

E237324E01


Text in Illustration 
*1
Speedometer, fuel receiver gauge, shift indicator
*2
Multi-information display
*3
Each indicator light, warning light
-
-

INPUT AND OUTPUT SIGNALS OF COMBINATION METER ASSEMBLY
  1. Meter or Gauge

    Item
    Condition
    Input/Output
    CAN/Direct line
    Signal
    Component
    Speedometer
    Display
    Input
    CAN
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    -
    Direct line
    Vehicle speed (SI)
    -
    Output
    CAN
    Vehicle speed
    Related ECUs
    -
    Direct line
    Vehicle speed (SI)
    HV battery monitor
    Display
    Input
    CAN
    ECO zone display condition
    Power management control ECU
    Hybrid system indicator
    Display
    Input
    CAN
    Hybrid system indicator condition
    Power management control ECU
    Fuel receiver gauge
    Display
    Input
    CAN
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Shift selection P
    Power management control ECU
    Shift selection N
    Parking brake switch
    Main body ECU (multiplex network body ECU)
    Direct line
    Fuel level
    Fuel sender gauge assembly
    Vehicle speed (SI)
    Brake booster assembly (skid control ECU)
    Output
    CAN
    Fuel receiver gauge indication
    ECM

  2. Warning or Indicator

    Item
    Condition
    Input/Output
    CAN/Direct line
    Signal
    Component
    Turn indicator
    Blinks
    Input
    Direct line
    LH turn signal switch
    Headlight dimmer switch assembly
    RH turn signal switch
    Hazard signal warning switch
    Hazard warning signal switch assembly
    -
    Output
    Direct line
    LH turn indicator output
    Each turn signal light
    RH turn indicator output
    High beam indicator
    Comes on
    Input
    Direct line
    DIM relay
    DIM relay
    Head indicator (with mph units)
    Comes on
    Input
    Direct line
    Headlight relay
    Headlight relay
    Tail indicator (with km/h units)
    Comes on
    Input
    TAIL relay
    TAIL relay
    Front fog indicator (w/ Front Fog Light)
    Comes on
    Input
    Direct line
    FR FOG relay
    FR FOG relay
    ECO MODE indicator
    Comes on
    Input
    CAN
    ECO MODE indicator
    Power management control ECU
    EV MODE indicator (EV drive mode display)
    Comes on/Blinks
    Input
    CAN
    EV mode message
    Power management control ECU
    Brake warning
    Comes on
    Input
    CAN
    Brake warning
    Brake booster assembly (skid control ECU)
    Parking brake switch
    Main body ECU (multiplex network body ECU)
    Electronically controlled brake warning
    Comes on/Blinks
    Input
    CAN
    Electronically controlled brake warning
    Brake booster assembly (skid control ECU)
    Slip indicator
    Comes on/Blinks
    Input
    CAN
    Slip indicator
    Brake booster assembly (skid control ECU)
    ABS warning
    Comes on/Blinks
    Input
    CAN
    ABS warning
    Brake booster assembly (skid control ECU)
    EPS warning
    Comes on/Blinks
    Input
    CAN
    EPS warning
    Power steering ECU assembly
    Security indicator
    Blinks
    Input
    Direct line
    Auto alarm condition
    Certification ECU (smart key ECU assembly)
    Cruise control indicator (green) (w/ Cruise Control System)
    Comes on
    Input
    CAN
    Cruise control indicator condition
    Power management control ECU
    Set (w/ Cruise Control System)
    Comes on
    Input
    CAN
    Cruise control set indicator condition
    Power management control ECU
    Charge warning
    Comes on
    Input
    CAN
    Charge malfunction
    Power management control ECU
    Tire pressure warning (w/ Tire Pressure Warning System)
    Comes on/Blinks
    Input
    CAN
    Tire pressure warning light condition
    Main body ECU (multiplex network body ECU)
    MIL (check engine warning light)
    Comes on
    Input
    Direct line
    MIL (check engine warning light)
    ECM
    SRS warning
    Comes on
    Input
    CAN
    SRS warning light comes on or blinks request
    Airbag sensor assembly
    Driver or front passenger seat belt warning
    Comes on/Blinks
    Input
    CAN
    Driver seat buckle switch
    Main body ECU (multiplex network body ECU)
    Parking brake switch
    Shift selection P
    Power management control ECU
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Direct line
    Vehicle speed (SI)
    Brake booster assembly (skid control ECU)
    CAN
    Front passenger seat buckle switch
    Airbag sensor assembly
    Front passenger seat occupant detection sensor
    EV indicator
    Comes on
    Input
    CAN
    Engine mode ID
    Power management control ECU
    Engine speed
    ECM
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    READY indicator
    Comes on
    Input
    CAN
    Ready display
    Power management control ECU
    Blinks
    Input
    CAN
    Starter
    Power management control ECU
    Master warning
    Comes on/Blinks
    Input
    CAN/Direct line
    Each warning
    Related ECUs
    Shift selection indicator
    Comes on
    Input
    CAN
    Shift selection P
    Power management control ECU
    Shift selection R
    Shift selection N
    Shift selection D
    Shift selection B

  3. Multi-information display

    Item
    Condition
    Input/Output
    CAN/Direct line
    Signal
    Component
    Opening
    Displayed
    -
    -
    -
    -
    ODO/TRIP meter
    Displayed
    Input
    CAN
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    Vehicle speed (SP1)
    Direct line
    Vehicle speed (SI)
    Brake booster assembly (skid control ECU)
    ODO/TRIP change switch
    Steering pad switch assembly
    Average fuel consumption after power switch on (READY)
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    Vehicle speed (SP1)
    Fuel consumption volume
    ECM
    Clock
    Displayed
    Input
    Direct line
    ODO/TRIP change switch
    Steering pad switch assembly
    DISP switch
    Meter illumination
    Illumination level
    Input
    Direct line
    Light control rheostat
    Light control rheostat
    Energy monitor
    Displayed
    Input
    CAN
    Energy flow (engine to wheels)
    Power management control ECU
    Energy flow (engine to motor)
    Energy flow (motor to wheels)
    Energy flow (motor to HV battery)
    Shift selection R
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Average vehicle speed after power switch on (READY)
    (Drive information)
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    Vehicle speed (SP1)
    Direct line
    Vehicle speed (SI)
    Driving time
    (Drive information)
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    EV running ratio
    (Drive information)
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Engine mode ID signal
    Engine speed signal
    ECM
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    EV travel distance
    (Drive information)
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Engine mode ID signal
    Engine speed signal
    ECM
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Driving distance
    (Drive information)
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    Fuel consumption volume
    ECM
    Direct line
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Fuel level
    Fuel sender gauge assembly
    Outside temperature
    (Drive information)
    Displayed
    Input
    CAN
    Outside temperature
    Air conditioner amplifier assembly
    ECO score
    Displayed
    Input
    CAN
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Acceleration opening angle
    Power management control ECU
    ECO zone display condition
    Shift selection P
    Shift selection R
    Shift selection N
    5 minutes fuel consumption
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Fuel consumption volume
    ECM
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    Vehicle speed (SP1)
    Direct line
    Vehicle speed (SI)
    ECO savings/ECO savings record
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Fuel consumption volume
    ECM
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    Vehicle speed (SP1)
    Direct line
    DISP switch
    Steering pad switch assembly
    TRIP switch
    Steering switch
    Fuel level
    Fuel sender gauge assembly
    Vehicle speed (SI)
    Brake booster assembly (skid control ECU)
    Past record
    Displayed
    Input
    CAN
    Ready display
    Power management control ECU
    Fuel consumption volume
    ECM
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    Vehicle speed (SP1)
    Direct line
    DISP switch
    Steering pad switch assembly
    TRIP switch
    Steering switch
    Vehicle speed (SI)
    Brake booster assembly (skid control ECU)
    Setting & screen off
    Displayed
    Input
    Direct line
    Steering switch
    Steering pad switch assembly
    Diagnostic trouble code
    Displayed
    Input
    CAN
    Each diagnostic trouble code
    Related ECUs
    MAINTENANCE MODE
    Displayed
    Input
    CAN
    Maintenance mode
    Power management control ECU
    CERTIFICATION MODE
    Displayed
    Input
    CAN
    Certification mode
    Certification mode
    Each door ajar
    Displayed
    Input
    CAN
    Driver door courtesy switch
    Main body ECU (multiplex network body ECU)
    Front passenger door courtesy switch
    Rear right door courtesy switch
    Rear left door courtesy switch
    Back door courtesy switch
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Direct line
    Vehicle speed (SI)
    AUTO POWER OFF TO CONSERVE BATTERY
    Displayed
    Input
    CAN
    Push start message request
    Power management control ECU
    SHIFT TO P POSITION
    Displayed
    Input
    CAN
    Smart key system alert 2 (Shift selection alert)
    Certification ECU (smart key ECU assembly)
    Push start message request
    Power management control ECU
    SHIFT TO P POSITION WHEN PARKED
    Displayed
    Input
    CAN
    NDB warning
    Power management control ECU
    N POSITION
    Displayed
    Input
    CAN
    Accelerator depressed with shift selection N
    Power management control ECU
    TRACTION BATTERY PRESERVATION MODE, RESTART AFTER SHIFTING TO THE P POSITION
    Displayed
    Input
    CAN
    Hybrid battery low voltage warning ID
    Power management control ECU
    LOW TRACTION BATTERY, CHARGES WHEN NOT IN N POSITION
    Displayed
    Input
    CAN
    Hybrid battery low voltage warning ID
    Power management control ECU
    RELEASE PARKING BRAKE
    Displayed
    Input
    CAN
    Parking brake switch
    Main body ECU (multiplex network body ECU)
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    KEY NOT DETECTED
    Displayed
    Input
    CAN
    Smart key system alert 1 (Key not detected in vehicle)
    Certification ECU (smart key ECU assembly)
    CHECK SMART KEY SYSTEM
    Displayed
    Input
    CAN
    Smart key system alert 1 (Smart key system malfunction alert)
    Certification ECU (smart key ECU assembly)
    WATER TEMPERATURE
    Displayed
    Input
    CAN
    Exhaust heat recirculation system existence
    Air conditioner amplifier assembly
    Water temperature
    ECM
    Direct line
    Water temperature
    Water temperature sensor
    CHECK HYBRID SYSTEM STOP THE VEHICLE IN A SAFE PLACE IMMEDIATELY
    Displayed
    Input
    CAN
    Hybrid system fail-safe warning
    Power management control ECU
    HYBRID SYSTEM OVERHEAT OUTPUT POWER IS LIMITED
    Displayed
    Input
    CAN
    Motor inverter high temperature malfunction ID
    Power management control ECU
    ENGINE OIL PRESSURE LOW
    Displayed
    Input
    CAN
    Oil pressure warning light comes on prohibition request
    Power management control ECU
    Direct line
    Oil pressure switch
    Engine oil pressure switch assembly
    TURN POWER OFF
    Displayed
    Input
    CAN
    Smart key system alert 2 (turn power off request display)
    Certification ECU (smart key ECU assembly)
    Push start message request
    Power management control ECU
    KEY DETECTED IN VEHICLE
    Displayed
    Input
    CAN
    Smart key system alert 3 (Key detected in vehicle)
    Certification ECU (smart key ECU assembly)
    TURN LIGHTS OFF
    Displayed
    Input
    CAN
    Lighting system state
    Main body ECU (multiplex network body ECU)
    Driver door courtesy switch
    Direct line
    TAIL relay
    TAIL relay
    DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY
    Displayed
    Input
    CAN
    Smart key system alert 1 (Emergency operation display)
    Certification ECU (smart key ECU assembly)
    DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START
    Displayed
    Input
    CAN
    Smart key system alert 3 (Engine start operation display)
    Certification ECU (smart key ECU assembly)
    Push start message request
    Power management control ECU
    SHIFT TO P POSITION TO START
    Displayed
    Input
    CAN
    Push start message request
    Power management control ECU
    STEERING LOCK ACTIVE
    Displayed
    Input
    CAN
    Smart key system alert 1 (Steering lock active alert)
    Certification ECU (smart key ECU assembly)
    KEY BATTERY LOW
    Displayed
    Input
    CAN
    Smart key system alert 1 (Key battery low alert)
    Certification ECU (smart key ECU assembly)
    MAINTENANCE REQUIRED SOON (for U.S.A.)
    Displayed
    Input
    CAN
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    MAINTENANCE REQUIRED (for U.S.A.)
    Displayed
    Input
    CAN
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    RESETTING MAINTENANCE DATA (for U.S.A.)
    Display
    Input
    CAN
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    RESETTING OF MAINTENANCE DATA INCOMPLETE (for U.S.A.)
    Displayed
    Input
    CAN
    Vehicle speed integrated value
    Brake booster assembly (skid control ECU)
    HYBRID SYSTEM OVERHEAT
    Displayed
    Input
    CAN
    Motor inverter temperature high malfunction
    Power management control ECU
    CHECK CRUISE CONTROL SYSTEM
    Displayed
    Input
    CAN
    Cruise control system warning
    Power management control ECU
    POWER ON
    Displayed
    Input
    CAN
    Smart key system alert 1 (Power on display)
    Certification ECU (smart key ECU assembly)
    SMART KEY SYSTEM INDICATOR
    Displayed
    Input
    CAN
    Smart key system alert 1 (Engine start possible display)
    Certification ECU (smart key ECU assembly)
    EV MODE CURRENTLY NOT AVAILABLE
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (another)))
    Power management control ECU
    EV MODE NOT AVAILABLE: WARMING UP
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (warming up)))
    Power management control ECU
    EV MODE NOT AVAILABLE: LOW BATTERY
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (battery)))
    Power management control ECU
    EV MODE NOT AVAILABLE: EXCESSIVE SPEED
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (speed)))
    Power management control ECU
    EV MODE NOT AVAILABLE: EXCESSIVE ACCELERATION
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (acceleration)))
    Power management control ECU
    EV MODE DEACTIVATED
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (another)))
    Power management control ECU
    EV MODE DEACTIVATED: LOW BATTERY
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (battery)))
    Power management control ECU
    EV MODE DEACTIVATED: EXCESSIVE SPEED
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (speed)))
    Power management control ECU
    EV MODE DEACTIVATED: EXCESSIVE ACCELERATION
    Displayed
    Input
    CAN
    EV mode message (goes off (Reject when EV switch operation (acceleration)))
    Power management control ECU
    Display change
    Displayed (change)
    Input
    Direct line
    DISP switch
    Steering pad switch assembly
    Steering pad switch

  4. Buzzer

    Item
    Condition
    Input/Output
    CAN/Direct line
    Signal
    Component
    Key reminder
    Sounds intermittently
    Input
    CAN
    Power switch (w/o Smart Key System)
    Main body ECU (multiplex network body ECU)
    Driver door courtesy switch
    Seat belt warning (for driver)
    Sounds once/intermittently
    Input
    CAN
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Driver seat buckle switch
    Main body ECU (multiplex network body ECU)
    Parking brake switch
    Shift selection P
    Power management control ECU
    Shift selection R
    Direct line
    Vehicle speed (SI)
    Brake booster assembly (skid control ECU)
    Seat belt warning (for front passenger)
    Sounds once/intermittently
    Input
    CAN
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Shift selection P
    Power management control ECU
    Shift selection R
    Parking brake switch
    Main body ECU (multiplex network body ECU)
    Front passenger seat buckle switch
    Airbag sensor assembly
    Front passenger seat occupant detection sensor
    Direct line
    Vehicle speed (SI)
    Brake booster assembly (skid control ECU)
    Smart key system
    Sounds continuously/intermittently
    Input
    CAN
    Meter buzzer (continuous)
    Certification ECU (smart key ECU assembly)
    Meter buzzer (Intermittent)
    Sounds intermittently (Maximum 9 times)
    Meter buzzer (Intermittent) (0.7 second cycle)
    Sounds once
    Meter buzzer (single)
    Driving with door ajar warning
    Sounds intermittently
    Input
    CAN
    Driver door courtesy switch
    Main body ECU (multiplex network body ECU)
    Front passenger door courtesy switch
    Rear right door courtesy switch
    Rear left door courtesy switch
    Back door courtesy switch
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Immobiliser certification completion
    Sounds once
    Input
    CAN
    Immobiliser certification completion
    Certification ECU (smart key ECU assembly)
    Driving with parking brake unreleased warning
    Sounds intermittently
    Input
    CAN
    Vehicle speed (SP1)
    Brake booster assembly (skid control ECU)
    Parking brake switch
    Main body ECU (multiplex network body ECU)
    P selection request
    Continuously
    Input
    CAN
    NDB warning
    Power management control ECU
    Hybrid battery low voltage
    Continuously
    Input
    CAN
    Hybrid battery low voltage warning ID
    Power management control ECU
    Hybrid battery charge request
    Sounds intermittently
    Input
    CAN
    Hybrid battery low voltage warning ID
    Power management control ECU
    EV reject
    Sounds twice
    Input
    CAN
    EV mode message
    Power management control ECU
    READY
    Sounds once
    Input
    CAN
    Ready buzzer
    Power management control ECU
    EPS warning
    Sounds once
    Input
    CAN
    EPS warning
    Power steering ECU assembly
    Low fuel warning
    Sounds once
    Input
    Direct line
    Fuel level
    Fuel sender gauge assembly
    Brake control system power low warning
    Sounds intermittently
    Input
    CAN
    Buzzer request (brake control system power low warning)
    Brake booster assembly (skid control ECU)
    Brake system temperature rise or active test
    Sounds intermittently
    Input
    CAN
    Buzzer request (brake system temperature rise or active test)
    Brake booster assembly (skid control ECU)
    Hill-start assist control (reset)
    Sounds twice
    Input
    CAN
    Buzzer request (hill-start assist control (reset)
    Brake booster assembly (skid control ECU)
    Hill-start assist control (set)
    Sounds once
    Input
    CAN
    Buzzer request (hill-start assist control (set)
    Brake booster assembly (skid control ECU)
    Turn signal flasher
    Sounds intermittently
    Input
    Direct line
    LH turn signal switch
    Headlight dimmer switch assembly
    RH turn signal switch
    Hazard signal warning switch
    Hazard warning signal switch assembly
    Hybrid system check
    Sounds intermittently
    Input
    CAN
    Hybrid system fail-safe warning (hybrid system malfunction notification on)
    Power management control ECU
    Sounds once
    Hybrid system fail-safe warning
    -
    Output
    Hybrid system fail-safe warning
    Accelerator depressed with shift selection N
    Continuously
    Input
    CAN
    Accelerator depressed with shift selection N
    Power management control ECU
    Multi-information display warning
    Sounds once
    Input
    CAN
    Multi-information display warning
    Related ECUs

  5. Others

    Item
    Condition
    Input/Output
    CAN/Direct line
    Signal
    Component
    Meter illumination
    Illumination level
    Input
    Direct line
    Light control rheostat
    Light control rheostat
    CAN
    Auto dimmer
    Main body ECU (multiplex network body ECU)
    -
    Output
    CAN
    Light control rheostat
    Related ECUs
    Direct line
    Illumination level signal
    Related ECUs
    Steering switch guidance (touch tracer) (w/ Touch Tracer)
    Display
    Input
    CAN
    Set temperature
    Air conditioner amplifier assembly
    REC select
    FRS select
    Direct line
    Steering switch
    Steering pad switch assembly


MULTI-INFORMATION DISPLAY FLOW CHART


  1. Multi-information display flow chart


    E249142E01


    Display Change Condition:

    Item
    Display Change Condition
    *a
    Conditions are met.
    *b
    Conditions are not met.
    *c
    Item or display is selected by operating the DISP switch.
    *d
    If there are multiple display requests, items will be displayed in sequence.
    *e
    ECO drive level display is displayed for a certain period of time after the power switch is turned off.


EACH WARNING DISPLAY


  1. Each warning display for the combination meter assembly is shown below.

    HINT:
    Illustrations may differ from the actual screen displayed depending on the specifications of the vehicle.


    E249161E01


    E249160E01


    E249141E01