Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Rear Power Window)

B164269E28

  1. Disconnect the J1 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J1-1 (E) - Body ground
    LA - Body ground
    Ground
    Always
    Below 1 Ω
    J1-6 (B) - J1-1 (E)
    LA-GR - LA
    Power supply
    Ignition switch ON (IG)
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J1 power window regulator master switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J1-8 (U) - J1-1 (E)
    R - LA
    Power window motor UP output
    Ignition switch ON (IG), driver door power window switch OFF → UP (Manual operation)
    11 to 14 V → Below 1 V
    J1-4 (AUTO) - J1-1 (E)
    R - LA
    Power window motor AUTO UP output
    Ignition switch ON (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    Power window motor AUTO DOWN output
    Ignition switch ON (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    J1-5 (D) - J1-1 (E)
    G - LA
    Power window motor DOWN output
    Ignition switch ON (IG), driver door power window switch OFF → DOWN (Manual operation)
    11 to 14 V → Below 1 V
    J1-16 (U) - J1-1 (E)
    LA-W - LA
    Power window motor UP output
    Ignition switch ON (IG), front passenger door power window switch OFF → UP (Manual operation)
    Below 1 V → 11 to 14 V
    J1-15 (D) - J1-1 (E)
    LA-P - LA
    Power window motor DOWN output
    Ignition switch ON (IG), front passenger door power window switch OFF → DOWN (Manual operation)
    Below 1 V → 11 to 14 V
    J1-12 (U) - J1-1 (E)
    LA-Y - LA
    Power window motor UP output
    Ignition switch ON (IG), rear LH door power window switch OFF → UP (Manual operation)
    Below 1 V → 11 to 14 V
    J1-13 (D) - J1-1 (E)
    LA-B - LA
    Power window motor DOWN output
    Ignition switch ON (IG), rear LH door power window switch OFF → DOWN (Manual operation)
    Below 1 V → 11 to 14 V
    J1-10 (U) - J1-1 (E)
    LA-R - LA
    Power window motor UP output
    Ignition switch ON (IG), rear RH door power window switch OFF → UP (Manual operation)
    Below 1 V → 11 to 14 V
    J1-18 (D) - J1-1 (E)
    LA-G - LA
    Power window motor DOWN output
    Ignition switch ON (IG), rear RH door power window switch OFF → DOWN (Manual operation)
    Below 1 V → 11 to 14 V
    If the result is not as specified, the power window regulator master switch assembly may be malfunctioning.


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Rear Window)

B164269E28

  1. Disconnect the J1 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J1-7 (E) - Body ground
    LA - Body ground
    Ground
    Always
    Below 1 Ω
    J1-15 (B) - J1-7 (E)
    LA-GR - LA
    Power supply
    Ignition switch ON (IG)
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J1 power window regulator master switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J1-18 (U) - J1-7 (E)
    R - LA
    Power window motor UP output
    Ignition switch ON (IG), driver door power window switch OFF → UP (Manual operation)
    11 to 14 V → Below 1 V
    J1-1 (AUTO) - J1-7 (E)
    R - LA
    Power window motor AUTO UP output
    Ignition switch ON (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed
    11 to 14 V → Below 1 V → 11 to 14 V
    Power window motor AUTO DOWN output
    Ignition switch ON (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open
    11 to 14 V → Below 1 V → 11 to 14 V
    J1-16 (D) - J1-7 (E)
    LA-P - LA
    Power window motor DOWN output
    Ignition switch ON (IG), driver door power window switch OFF → DOWN (Manual operation)
    11 to 14 V → Below 1 V
    J1-12 (U) - J1-7 (E)
    LA-W - LA
    Power window motor UP output
    Ignition switch ON (IG), front passenger door power window switch OFF → UP (Manual operation)
    Below 1 V → 11 to 14 V
    J1-16 (D) - J1-7 (E)
    LA-P - LA
    Power window motor DOWN output
    Ignition switch ON (IG), front passenger door power window switch OFF → DOWN (Manual operation)
    Below 1 V → 11 to 14 V
    If the result is not as specified, the power window regulator master switch assembly may be malfunctioning.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Door)

B164270E36

  1. Disconnect the H2 power window regulator switch assembly (for front passenger door) connector.

  2. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H2-3 (B) - Body ground
    LA-L - Body ground
    Power supply
    Ignition switch ON (IG)
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the H2 power window regulator switch assembly (for front passenger door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H2-4 (U) - Body ground
    LA-R - Body ground
    Power window motor UP output
    Ignition switch ON (IG), front passenger door power window switch OFF → UP (Manual operation)
    Below 1 V → 11 to 14 V
    H2-1 (D) - Body ground
    LA-G - Body ground
    Power window motor DOWN output
    Ignition switch ON (IG), front passenger door power window switch OFF → DOWN (Manual operation)
    Below 1 V → 11 to 14 V
    If the result is not as specified, the power window regulator switch assembly (for front passenger door) may be malfunctioning.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Door) (w/ Rear Power Window)

B164270E37

  1. Disconnect the L1 power window regulator switch assembly (for rear LH door) connector.

  2. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L1-3 (B) - Body ground
    LA-SB - Body ground
    Power supply
    Ignition switch ON (IG)
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L1 power window regulator switch assembly (for rear LH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L1-4 (U) - Body ground
    LA-Y - Body ground
    Power window motor UP output
    Ignition switch ON (IG), rear LH door power window switch OFF → UP (Manual operation)
    Below 1 V → 11 to 14 V
    L1-1 (D) - Body ground
    LA-B - Body ground
    Power window motor DOWN output
    Ignition switch ON (IG), rear LH door power window switch OFF → DOWN (Manual operation)
    Below 1 V → 11 to 14 V
    If the result is not as specified, the power window regulator switch assembly (for rear LH door) may be malfunctioning.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Door) (w/ Rear Power Window)

B164270E38

  1. Disconnect the K1 power window regulator switch assembly (for rear RH door) connector.

  2. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K1-3 (B) - Body ground
    LA-SB - Body ground
    Power supply
    Ignition switch ON (IG)
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K1 power window regulator switch assembly (for rear RH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K1-4 (U) - Body ground
    LA-Y - Body ground
    Power window motor UP output
    Ignition switch ON (IG), rear RH door power window switch OFF → UP (Manual operation)
    Below 1 V → 11 to 14 V
    K1-1 (D) - Body ground
    LA-B - Body ground
    Power window motor DOWN output
    Ignition switch ON (IG), rear RH door power window switch OFF → DOWN (Manual operation)
    Below 1 V → 11 to 14 V
    If the result is not as specified, the power window regulator switch assembly (for rear RH door) may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Door)

B286758E13

  1. Disconnect the J3 power window regulator motor assembly LH (for driver door) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-1 (GND) - Body ground
    LA - Body ground
    Ground
    Always
    Below 1 Ω
    J3-2 (B) - Body ground
    LA-G - Body ground
    Power supply
    Ignition switch off
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J3 power window regulator motor assembly LH (for driver door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-4 (AUTO) - J3-1 (GND)
    R - LA
    Power window motor AUTO UP input
    Ignition switch ON (IG), driver door power window fully open
    11 to 14 V
    J3-4 (AUTO) - J3-1 (GND)
    R - LA
    Power window motor AUTO UP input
    Ignition switch ON (IG), driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    J3-4 (AUTO) - J3-1 (GND)
    R - LA
    Power window motor AUTO UP input
    Ignition switch ON (IG), driver door power window fully closed
    11 to 14 V
    J3-4 (AUTO) - J3-1 (GND)
    R - LA
    Power window motor AUTO DOWN input
    Ignition switch ON (IG), driver door power window fully closed
    11 to 14 V
    J3-4 (AUTO) - J3-1 (GND)
    R - LA
    Power window motor AUTO DOWN input
    Ignition switch ON (IG), driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    J3-4 (AUTO) - J3-1 (GND)
    R - LA
    Power window motor AUTO DOWN input
    Ignition switch ON (IG), driver door power window fully open
    11 to 14 V
    J3-5 (LED) - J3-1 (GND)
    W - LA
    LED illumination signal
    Ignition switch ON (IG)
    11 to 14 V
    J3-5 (LED) - J3-1 (GND)
    W - LA
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    J3-7 (DOWN) - J3-1 (GND)
    G - LA
    Power window motor DOWN input
    Ignition switch ON (IG), driver door power window regulator switch not pushed or pulled
    11 to 14 V
    J3-7 (DOWN) - J3-1 (GND)
    G - LA
    Power window motor DOWN input
    Ignition switch ON (IG), driver door power window regulator switch pushed halfway down (Manual operation)
    Below 1 V
    J3-7 (DOWN) - J3-1 (GND)
    G - LA
    Power window motor DOWN input
    Ignition switch ON (IG), driver door power window fully closed
    11 to 14 V
    J3-7 (DOWN) - J3-1 (GND)
    G - LA
    Power window motor DOWN input
    Ignition switch ON (IG), driver door power window regulator switch fully pushed down (Automatic position)
    Below 1 V
    J3-7 (DOWN) - J3-1 (GND)
    G - LA
    Power window motor DOWN input
    Ignition switch ON (IG), driver door power window fully open
    11 to 14 V
    J3-10 (UP) - J3-1 (GND)
    R - LA
    Power window motor UP input
    Ignition switch ON (IG), driver door power window regulator switch not pushed or pulled
    11 to 14 V
    J3-10 (UP) - J3-1 (GND)
    R - LA
    Power window motor UP input
    Ignition switch ON (IG), driver door power window regulator switch pulled halfway up (Manual operation)
    Below 1 V
    J3-10 (UP) - J3-1 (GND)
    R - LA
    Power window motor UP input
    Ignition switch ON (IG), driver door power window fully open
    11 to 14 V
    J3-10 (UP) - J3-1 (GND)
    R - LA
    Power window motor UP input
    Ignition switch ON (IG), driver door power window regulator switch fully pulled up (Automatic operation)
    Below 1 V
    J3-10 (UP) - J3-1 (GND)
    R - LA
    Power window motor UP input
    Ignition switch ON (IG), driver door power window fully closed
    11 to 14 V
    If the result is not as specified, the power window regulator motor assembly LH (for driver door) may be malfunctioning.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


  1. Disconnect the MB main body ECU (multiplex network body ECU) connector.


    B281049E05

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    MB-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON (IG)
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the MB main body ECU (multiplex network body ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G59-2 (KOFF) - Body ground
    L - Body ground
    Power window relay operation signal
    Ignition switch ON (IG)
    11 to 14 V
    G59-2 (KOFF) - Body ground
    L - Body ground
    Power window relay operation signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door courtesy switch LH input
    Front door LH open
    Below 1 V
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door courtesy switch LH input
    Front door LH closed
    Pulse generation
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door courtesy switch RH input
    Front door RH open
    Below 1 V
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door courtesy switch RH input
    Front door RH closed
    Pulse generation
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.