Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER ASSEMBLY


  1. Disconnect the G1 combination meter assembly connector.


    E238019E03

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G1-20 (ET) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the G1 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G1-21 (IG+) - Body ground
    B - Body ground
    Ignition power supply
    (IG signal)
    Ignition switch off
    Below 1 V
    G1-21 (IG+) - Body ground
    B - Body ground
    Ignition power supply
    (IG signal)
    Ignition switch ON (IG)
    11 to 14 V
    If the result is not as specified, the combination meter assembly may have a malfunction.


CHECK AIRBAG SENSOR ASSEMBLY

C123353E59


Terminal No.
Terminal Symbol
Destination
M36-11
LBE+
Front seat inner belt assembly LH
M36-12
LBE-
Front seat inner belt assembly LH
M37-12
FSR+
Occupant detection ECU
M37-13
FSR-
Occupant detection ECU

CHECK OCCUPANT DETECTION ECU


  1. Measure the voltage according to the value(s) in the table below.


    C238368E08


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specification
    Y3-1 (+B) - Y3-3 (GND)
    W - W-B
    Auxiliary battery
    Ignition switch off
    11 to 14 V
    Y3-2 (DIA) - Y3-3 (GND)
    GR - W-B
    Diagnosis (DLC3)
    Ignition switch ON (IG), Techstream not connected to DLC3
    Below 1 V
    Y3-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    Y3-4 (FSR-) - Y3-3 (GND)
    LG - W-B
    Airbag sensor assembly communication line
    Always
    Below 1 V
    Y3-5 (BGND) - Y3-3 (GND)
    P - W-B
    Front passenger buckle switch ground line
    Always
    Below 1 V
    Y3-6 (IG) - Y3-3 (GND)
    B - W-B
    Power source
    Ignition switch ON (IG)
    11 to 14 V
    Y3-7 (FSR+) - Y3-4 (FSR-)
    L - LG
    Airbag sensor assembly communication line
    Ignition switch ON (IG)
    Pulse generation
    Y3-8 (BSW) - Y3-5 (BGND)
    G - P
    Front passenger buckle switch line
    Always
    Pulse generation
    Y2-1 (SVC3) - Y2-5 (SGD3)
    GR - W
    Occupant classification sensor LH power supply line
    Ignition switch ON (IG)
    4.9 to 5.1 V
    Y2-2 (SVC4) - Y2-6 (SGD4)
    V - BR
    Occupant classification sensor RH power supply line
    Ignition switch ON (IG)
    4.9 to 5.1 V
    Y2-3 (SIG3) - Y2-5 (SGD3)
    SB - W
    Occupant classification sensor LH signal line
    Ignition switch ON (IG)
    Pulse generation
    Y2-4 (SIG4) - Y2-6 (SGD4)
    B - BR
    Occupant classification sensor RH signal line
    Ignition switch ON (IG)
    Pulse generation
    If the result is not as specified, the occupant detection ECU may have a malfunction.