Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0617-142    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

The power management control ECU monitors the ST signal received from the ignition or starter switch assembly. When an error is detected in the ST signal, this DTC is stored.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0617
142
Although the ignition switch is off, the power management control ECU receives a ST signal.
(1 trip detection logic)
  1. Power management control ECU
  2. Wire harness or connector
  3. Ignition or starter switch assembly

WIRING DIAGRAM


A148900E07


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the ignition switch off and wait for 30 seconds or more.
  2. Turn the ignition switch to ON (READY) and wait for 15 seconds or more.
  3. Turn the ignition switch off and wait for 30 seconds or more.

1.CHECK HARNESS AND CONNECTOR (ST2 TERMINAL VOLTAGE)
  1. Disconnect connector A39 from the power management control ECU.



    A250971E12
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A39-10 (ST2) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the power management control ECU connector.



NG
Go to step 4
OK


2.CLEAR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Read and record the DTCs and freeze frame data.

  1. Clear the DTCs and freeze frame data.

  1. Turn the ignition switch off.


NEXT


3.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Turn the ignition switch off and leave the vehicle as it is for approximately 5 seconds.

  1. Turn the ignition switch to ON (IG) again.

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Recheck for DTCs.

    Result:
    Result
    Proceed to
    P0617-142 is output again.
    A
    P0617-142 is not output.
    B

  1. Turn the ignition switch off.



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect connector G15 from the ignition or starter switch assembly connector.

  1. Disconnect connector A39 from the power management control ECU connector.



    A263707E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G15-7 (ST2) or A39-10 (ST2) - Body ground and other terminals
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition or Starter Switch Assembly)
    *b
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the power management control ECU connector.

  1. Connect the ignition or starter switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)