Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

POWER STEERING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the ignition switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the ignition switch to ON (IG).

  4. Turn the Techstream on.

  5. Enter the following menus: Chassis / EMPS / Data List.

  6. According to the display on the Techstream, read the "Data List".


EMPS 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Meter Vehicle Velocity
Vehicle speed from meter/
Min.: 0.0 km/h (0.0mph)
Max.: 300.0 km/h (186.4 mph)
0 km/h (0 mph)
Ignition switch ON (READY) and vehicle stopped
No significant fluctuation
Ignition switch ON (READY) and vehicle driven at constant speed
Motor Actual Current
Current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
-The value increases when turning right and decreases when turning left
Ignition switch ON (READY) and steering wheel being turned
Command Value Current
Requested current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
-The value increases when turning right and decreases when turning left
Ignition switch ON (READY) and steering wheel being turned
Thermistor Temperature
ECU substrate temperature/
Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F)
-50 to 150°C (-58 to 302°F)
-
PIG Power Supply
Power source voltage to activate motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V
Always
IG Power Supply
ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V
Ignition switch ON (IG)
Steering Wheel Torque
Steering wheel torque/
Min.: -327.68 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort
Ignition switch ON (READY) and steering wheel being turned
Torque Sensor 1 Output
Torque sensor 1 output value/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V
Ignition switch ON (READY) and steering wheel not being turned (without load)
2.5 to 3.8 V
Ignition switch ON (READY) and steering wheel being turned to right with vehicle stopped
1.2 to 2.5 V
Ignition switch ON (READY) and steering wheel being turned to left with vehicle stopped
Torque Sensor 2 Output
Torque sensor 2 output value/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V
Ignition switch ON (READY) and steering wheel not being turned (without load)
1.2 to 2.5 V
Ignition switch ON (READY) and steering wheel being turned to right with vehicle stopped
2.5 to 3.8 V
Ignition switch ON (READY) and steering wheel being turned to left with vehicle stopped
TRQ1 Zero Point Value
Zero point value of torque sensor 1/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V
Ignition switch ON (READY) and steering wheel not being turned (without load)
TRQ2 Zero Point Value
Zero point value of torque sensor 2/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V
Ignition switch ON (READY) and steering wheel not being turned (without load)
Motor Terminal Volt(+)
Motor terminal M1 voltage/
Min.: 0.0 V
Max.: 25.5 V
9 to 16 V
Ignition switch ON (READY) and steering wheel being turned to right
6 to 8 V
Ignition switch ON (READY) and steering wheel being turned to left
Motor Terminal Volt(-)
Motor terminal M2 voltage/
Min.: 0.0 V
Max.: 25.5 V
6 to 8 V
Ignition switch ON (READY) and steering wheel being turned to right
9 to 16 V
Ignition switch ON (READY) and steering wheel turned to left
IG ON/OFF Times
Number of times of ignition switch ON/OFF after fail detection/
Min.: 0 time
Max.: 65535 times
-
This value indicates the number of times of IG ON/OFF after the latest DTC detection.
Motor Overheat Record
Continuous overheat prevention control record/
Unrec or Rec
Unrec
-
Motor Lo Power Record
PIG power source voltage drop record/
Unrec or Rec
Unrec
-
Eng Rev Inter Record
Record of ignition switch ON signal interruption/
Unrec or Rec
Unrec
-
Spd Sig Invalid Record
Vehicle speed signal invalid record/
Unrec or Rec
Unrec
-
Battery Voltage Lo Record
Battery voltage reduction history/
Min.: 0 times, Max.: 65535 times
0 to 65535
-
Ready Status
Ready status/
READY or OFF
READY or OFF
-
The Number of DTCs
Number of detected DTCs when freeze frame data stored/
Min.: 0
Max.: 255
0 to 255
-