REAR AXLE BEAM > REMOVAL |
| 1. PRECAUTION |
| 2. DISABLE BRAKE CONTROL |
Wait at least 2 minutes after turning the ignition switch off.
![]() |
Disconnect the reservoir level switch connector with the parking brake applied.
Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal can not be further depressed.
Release the parking brake.
| 3. REMOVE REAR WHEELS |
| 4. DRAIN BRAKE FLUID |
| 5. DISCONNECT SKID CONTROL SENSOR WIRE LH |
![]() |
Disengage the 3 claws and remove the connector cover.
![]() |
Disconnect the skid control sensor wire connector from the rear axle hub and bearing assembly.
| 6. DISCONNECT SKID CONTROL SENSOR WIRE RH |
| 7. SEPARATE SKID CONTROL SENSOR WIRE LH |
![]() |
Remove the nut and separate the skid control sensor wire LH.
| 8. SEPARATE SKID CONTROL SENSOR WIRE RH |
| 9. SEPARATE NO. 4 REAR BRAKE TUBE |
![]() |
Using a union nut wrench, separate the No. 4 rear brake tube while holding the rear flexible hose LH with a wrench.
Remove the clip and separate the rear flexible hose LH from the rear axle beam assembly.
Remove the nut and separate the No. 4 rear brake tube.
| 10. SEPARATE NO. 3 REAR BRAKE TUBE |
| 11. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Separate the No. 1 parking brake cable clamp from the rear axle beam assembly.
Remove the bolt and separate the No. 3 parking brake cable assembly.
Remove the No. 1 parking brake cable clamp from the No. 3 parking brake cable assembly .
| 12. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY |
| 13. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY |
Remove the 2 rear brake drum sub-assemblies .
| 14. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH |
![]() |
Remove the 4 bolts and rear axle hub and bearing assembly from the rear axle beam assembly.
| 15. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH |
| 16. LOOSEN REAR AXLE BEAM ASSEMBLY |
![]() |
Loosen the 2 bolts.
| *A | LH Side |
| *B | RH Side |
| 17. REMOVE REAR COIL SPRING LH |
Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.

| *1 | Wooden Block | *2 | Jack |
Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.
Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks, and remove the rear coil spring LH.
Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.
| 18. REMOVE REAR COIL SPRING RH |
| 19. REMOVE REAR UPPER COIL SPRING INSULATOR LH |
| 20. REMOVE REAR UPPER COIL SPRING INSULATOR RH |
| 21. REMOVE REAR LOWER COIL SPRING INSULATOR LH |
| 22. REMOVE REAR LOWER COIL SPRING INSULATOR RH |
| 23. REMOVE REAR AXLE BEAM ASSEMBLY |
Support the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools as shown in the illustration.

| *1 | Engine Lifter | *2 | Wooden Block |
| *3 | Attachment | - | - |
Remove the 2 bolts (A) and 2 nuts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.
Remove the 2 bolts (B) and rear axle beam assembly.