Home › Engine / Hybrid System › 1NZ-FXE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE SPARK PLUG


    A267420
  1. Using a 16 mm spark plug wrench, remove the 4 spark plugs.



2. REMOVE OIL FILLER CAP SUB-ASSEMBLY


    A269005
  1. Remove the oil filler cap sub-assembly from the cylinder head cover.



3. REMOVE OIL FILLER CAP GASKET


    A065656E05
  1. Using a screwdriver, remove the oil filler cap gasket from the oil filler cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Wrap the screwdriver tip with protective tape before use.



4. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A266945
  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



5. REMOVE CAMSHAFT POSITION SENSOR


    A266999
  1. Remove the bolt and camshaft position sensor.



6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A266998
  1. Remove the bolt and camshaft timing oil control valve assembly.



    A195062E09
  1. Remove the O-ring from the camshaft timing oil control valve assembly.



7. REMOVE KNOCK CONTROL SENSOR


    A268026
  1. Remove the bolt and knock control sensor.



8. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A275780
  1. Using a 19 mm union nut wrench, remove the engine coolant temperature sensor and gasket.



9. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A268027
  1. Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.



10. REMOVE OIL FILTER SUB-ASSEMBLY
  1. Using SST, remove the oil filter.

    SST
    09228-06501  



11. REMOVE CRANKSHAFT POSITION SENSOR


    A269006
  1. Remove the bolt and crankshaft position sensor.



12. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY


    A267959
  1. Remove the 2 bolts and water inlet with thermostat sub-assembly.



    A267962
  1. Remove the gasket from the water inlet with thermostat sub-assembly.



13. REMOVE ENGINE WATER PUMP ASSEMBLY


    A267965
  1. Remove the 5 bolts and engine water pump assembly.



    A267966
  1. Remove the gasket from the engine water pump assembly.



14. REMOVE WATER INLET HOUSING


    A266948
  1. Remove the bolt, 2 nuts and water inlet housing.

  1. Remove the gasket.



15. REMOVE ENGINE MOUNTING BRACKET RH


    A266946
  1. Remove the 4 bolts and engine mounting bracket RH.



16. REMOVE VENTILATION VALVE SUB-ASSEMBLY


    A269007
  1. Using a 19 mm deep socket wrench, remove the ventilation valve sub-assembly from the cylinder head cover sub-assembly.



17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A265764
  1. Remove the 9 bolts, 2 seal washers, 2 nuts and cylinder head cover sub-assembly.

  1. Remove the gasket from the cylinder head cover sub-assembly.



18. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY


  1. Set the No. 1 cylinder to TDC/compression.

    1. Turn the crankshaft damper until its notch and timing mark "0" of the timing chain cover are aligned.



    2. A268183E01
    3. Check that the timing marks on both the camshaft timing sprocket and the camshaft timing gear are facing upward as shown in the illustration.
      Text in Illustration 
      *a
      Timing Mark
      *b
      Timing Mark (Rectangle)
      *c
      Mark (Circle)
      *d
      Timing Notch

      HINT:
      1. There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.
      2. If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



    A267009E01
  1. Using SST, hold the crankshaft damper sub-assembly in place and loosen the bolt.

    SST
    09213-58012   (91111-50845)
    09330-00021  

    NOTICE:
    When installing SST, be careful that the bolt which holds SST does not interfere with the chain cover.



    A267010E01
  1. Using SST, remove the crankshaft damper sub-assembly and bolt.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    HINT:
    Apply a lubricant to the threads and end of SST.



    A265784
  1. Remove the crankshaft straight pin.



19. REMOVE TIMING CHAIN COVER


    A266812
  1. Remove the 18 bolts, nut and 2 wire harness clamp brackets.



    A266950E01
  1. Remove the timing chain cover by prying between the timing chain cover and oil pan, cylinder head or cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, oil pan, cylinder block, and cylinder head.

    HINT:
    Tape the screwdriver tip before use.



    A265759
  1. Remove the 2 O-rings from the cylinder block and oil pan.



20. REMOVE SCREW PLUG


    A266922
  1. Using a 8 mm hexagon socket wrench, remove the screw plug.



21. REMOVE OIL PUMP SEAL


    A156383E01
  1. Using a screwdriver and wooden block, remove the oil pump seal.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Wooden Block

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.



22. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A156304E01
  1. Turn the stopper plate of the No. 1 chain tensioner assembly clockwise and push in the plunger with the lock released.
    Text in Illustration 
    *1
    Hexagon Wrench
    *2
    Plunger
    *3
    Stopper Plate

  1. Turn the stopper plate of the No. 1 chain tensioner assembly counterclockwise and insert a hexagon wrench into the hole in the stopper plate to lock with the plunger pushed in.



    A116568
  1. Remove the 2 bolts and No. 1 chain tensioner assembly.

    NOTICE:
    Do not rotate the crankshaft with the No. 1 chain tensioner removed.



23. REMOVE CHAIN TENSIONER SLIPPER


    A265765
  1. Remove the chain tensioner slipper.



24. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A265766
  1. Remove the 2 bolts and No. 1 chain vibration damper.



25. REMOVE CHAIN SUB-ASSEMBLY


    A265767
  1. Remove the chain sub-assembly.

    NOTICE:
    When rotating the camshaft with the chain sub-assembly removed, rotate the crankshaft counterclockwise 40° from TDC and align the oil jet hole with the paint mark to prevent the pistons from coming into contact with the valves.



26. REMOVE FUEL DELIVERY PIPE


    A266997
  1. Remove the 3 bolts and fuel delivery pipe.



27. REMOVE FUEL DELIVERY SPACER


    A265001
  1. Remove the 2 fuel delivery spacers from the cylinder head.



28. REMOVE INJECTOR VIBRATION INSULATOR


    A268449
  1. Remove the 4 injector vibration insulators from the cylinder head.



29. REMOVE FUEL INJECTOR ASSEMBLY


    A265003E01
  1. Pull the 4 fuel injector assemblies out of the fuel delivery pipe.
    Text in Illustration 
    V100135
    Pull

  1. Remove the O-ring from each fuel injector.

  1. For reinstallation, attach a tag or label to each injector shaft.

    NOTICE:
    Prevent entry of foreign matter by covering the fuel injectors with plastic bags.



30. REMOVE NO. 2 CAMSHAFT


    A267006E01
  1. Using several steps, uniformly loosen and remove the 11 bolts in the sequence shown in the illustration. Then remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.

    NOTICE:
    Uniformly loosen the bolts while keeping the No. 2 camshaft level.



31. REMOVE CAMSHAFT TIMING GEAR OR SPROCKET


    A064874E01
  1. Clamp the No. 2 camshaft in a vise.

    NOTICE:
    Be careful not to damage the No. 2 camshaft.

  1. Remove the bolt and camshaft timing gear or sprocket.



32. REMOVE CAMSHAFT


    A267005E01
  1. Using several steps, uniformly loosen and remove the 8 bolts in the sequence shown in the illustration. Then remove the 4 No. 2 camshaft bearing caps.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.



33. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY


  1. Check the camshaft timing gear assembly lock.



      A267919
    1. Clamp the camshaft in a vise, and make sure that the camshaft timing gear assembly does not rotate.



  1. Release the lock pin.



      A266804E01
    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
      Text in Illustration 
      *a
      Retard Side Path
      *b
      Advance Side Path
      *c
      Open
      *d
      Close
      V100144
      Rubber Piece
      V100145
      Vinyl Tape

      HINT:
      4 oil paths are provided in the groove. Plug 2 paths with rubber pieces.

    2. Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.



    3. A146376E01
    4. Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the 2 paths (the advance side path and the retard side path).
      Text in Illustration 
      *a
      Advance Side Path
      *b
      Retard Side Path

      HINT:
      Cover the paths with a piece of cloth when applying pressure to keep oil from spraying.



    5. A146374E01
    6. Make sure that the camshaft timing sprocket turns in the retard direction when reducing the air pressure applied to the advance side path.
      Text in Illustration 
      *a
      Advance Side Path
      *b
      Retard Side Path
      *c
      Decompress
      *d
      Hold Pressure

      HINT:
      The lock pin is released and the camshaft timing sprocket turns in the retard direction.

    7. When the camshaft timing sprocket moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

      NOTICE:
      Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing sprocket may abruptly shift in the advance direction and break the lock pin or other parts.



34. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


    A032639E06
  1. Remove the bolt and camshaft timing gear assembly.
    Text in Illustration 
    *a
    Do Not Remove

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. When reusing the camshaft timing gear assembly, release the lock pin first, then install the camshaft timing gear assembly.



35. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A267008E01
  1. Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 washers with an 8 mm bi-hexagon wrench in the sequence shown in the illustration.

    NOTICE:
    1. When removing the cylinder head bolt, do not drop the washer into the cylinder head sub-assembly.
    2. Removing the bolts in the wrong order may cause damage to the cylinder head sub-assembly.

  1. Remove the cylinder head sub-assembly.



36. REMOVE CYLINDER HEAD GASKET


    A268213
  1. Remove the cylinder head gasket from the cylinder block.



37. REMOVE OIL FILTER UNION


    A269008
  1. Using a 12 mm hexagon socket wrench, remove the oil filter union.



38. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A265785
  1. Remove the oil pan drain plug and gasket.

  1. Remove the 9 bolts and 2 nuts.



    A088894
  1. Insert the blade of an oil pan seal cutter between the oil pan and No. 2 oil pan sub-assembly, cut the sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Be careful not to damage the oil pan and No. 2 oil pan sub-assembly.



39. REMOVE OIL STRAINER SUB-ASSEMBLY


    A084113
  1. Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.



40. REMOVE OIL PAN SUB-ASSEMBLY


    A265814
  1. Loosen and remove the 13 bolts uniformly in several steps.



    A265786E01
  1. Using a screwdriver, remove the oil pan sub-assembly by prying between the cylinder block and oil pan sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block.

    HINT:
    Wrap the screwdriver tip with protective tape before use.



    A088897
  1. Remove the 2 O-rings from the cylinder block.



    A089042
  1. Using an E5 "TORX" socket wrench, remove the 4 stud bolts.



41. REMOVE REAR ENGINE OIL SEAL


    A089043
  1. Remove the rear engine oil seal.