CYLINDER HEAD > INSPECTION |
| 1. INSPECT CYLINDER HEAD FOR FLATNESS |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block and manifold.
| *a | Cylinder Block Side |
| *b | Intake Manifold Side |
| *c | Exhaust Manifold Side |
| Surface | Specified Condition |
| Cylinder block side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.10 mm (0.00394 in.) |
| Exhaust manifold side | 0.10 mm (0.00394 in.) |
| 2. INSPECT CYLINDER HEAD FOR CRACKS |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.
If cracked, replace the cylinder head sub-assembly.
| 3. INSPECT INTAKE VALVE |
![]() |
Using a vernier caliper, measure the overall length of the intake valve.
| *a | Overall Length |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *a | Margin Thickness |
| 4. INSPECT EXHAUST VALVE |
![]() |
Using a vernier caliper, measure the overall length of the exhaust valve.
| *a | Overall Length |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *a | Margin Thickness |
| 5. INSPECT COMPRESSION SPRING |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
![]() |
Using a steel square, measure the deviation of the compression spring.
| *1 | Steel Square |
| *a | Deviation |
| 6. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the valve guide bush.
Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.
| Valve Guide Bush | Specified Condition |
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Guide Bush | Specified Condition |
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |
| 7. INSPECT VALVE SEATS |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
![]() |
Check the valve face and seat according to the following procedure.
| *a | Width |
If Prussian blue appears 360° around the valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears 360° around the valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contact is in the middle of the valve face with the valve seat width between 1.0 and 1.4 mm (0.0394 to 0.0551 in.).
| 8. INSPECT VALVE LIFTER |
![]() |
Using a micrometer, measure the valve lifter diameter.
| 9. INSPECT VALVE LIFTER OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the valve lifter bore diameter of the cylinder head sub-assembly.
Subtract the lifter diameter measurement from the lifter bore diameter measurement.
| 10. INSPECT CAMSHAFT |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
![]() |
Using a dial indicator, measure the circle runout at the center journal.
Inspect the cam lobes.
![]() |
Using a micrometer, measure the cam lobe height.
Inspect the camshaft journals.
![]() |
Using a micrometer, measure the journal diameter.
| Journal | Specified Condition |
| No. 1 journal | 34.449 to 34.465 mm (1.3563 to 1.3569 in.) |
| Other journals | 22.949 to 22.965 mm (0.90350 to 0.90413 in.) |
| 11. INSPECT NO. 2 CAMSHAFT |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
![]() |
Using a dial indicator, measure the circle runout at the center journal.
Inspect the cam lobes.
![]() |
Using a micrometer, measure the cam lobe height.
Inspect the camshaft journals.
![]() |
Using a micrometer, measure the journal diameter.
| Journal | Specified Condition |
| No. 1 journal | 34.449 to 34.465 mm (1.3563 to 1.3569 in.) |
| Other journals | 22.949 to 22.965 mm (0.90350 to 0.90413 in.) |
| 12. INSPECT CAMSHAFT THRUST CLEARANCE |
Install the camshafts .
![]() |
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 13. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the camshaft bearing caps and the camshaft journals.
Place the camshafts on the cylinder head sub-assembly.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
| *1 | Plastigage |
Install the camshaft bearing caps .
Remove the camshaft bearing caps .
![]() |
Measure the Plastigage at its widest point.
| *1 | Plastigage |