Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR

OUTER REAR VIEW MIRROR > INSPECTION

for Preparation Click here



1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


  1. Check the operation of the mirror surface.



      B281818E01
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Auxiliary battery positive (+) → Terminal 6 (MV)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns upward
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 6 (MV)
      Turns downward
      Auxiliary battery positive (+) → Terminal 4 (MH)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns left
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



  1. Check the operation of the mirror heater (w/ Mirror Heater).



      B281820E03
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (+) - 9 (-)
      25°C (77°F)
      8.5 to 11.5 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.

    3. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 8, then check that the mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      OK:
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.



2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


  1. Check the operation of the mirror surface.



      B281822E01
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Auxiliary battery positive (+) → Terminal 6 (MV)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns upward
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 6 (MV)
      Turns downward
      Auxiliary battery positive (+) → Terminal 4 (MH)
      Auxiliary battery negative (-) → Terminal 5 (M+)
      Turns left
      Auxiliary battery positive (+) → Terminal 5 (M+)
      Auxiliary battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



  1. Check the operation of the mirror heater (w/ Mirror Heater).



      B281824E02
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (+) - 9 (-)
      25°C (77°F)
      8.5 to 11.5 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.

    3. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 8, then check that the mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      OK:
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.