FRONT DRIVE SHAFT ASSEMBLY > REASSEMBLY |
| 1. INSTALL FRONT DRIVE SHAFT DUST COVER |
![]() |
Using a steel plate and a press, install a new front drive shaft dust cover into the front drive inboard joint assembly until it is flush with the end.
| *1 | Steel Plate |
| 2. INSTALL OUTBOARD JOINT BOOT |
![]() |
Wrap the splines of the front axle outboard joint shaft assembly with protective tape to prevent the boot from being damaged.
| *1 | Protective Tape |
![]() |
Install new parts onto the front axle outboard joint shaft assembly in the following order:
| *1 | Front Axle Outboard Joint Shaft Assembly |
| *2 | Front No. 2 Axle Outboard Joint Boot Clamp |
| *3 | Outboard Joint Boot |
| *4 | Front Axle Outboard Joint Boot Clamp |
![]() | Outboard Joint Side |
![]() | Inboard Joint Side |
Front No. 2 axle outboard joint boot clamp
Outboard joint boot
Front axle outboard joint boot clamp
Pack the joint portion of the front axle outboard joint shaft assembly and outboard joint boot with grease.
Install the outboard joint boot onto the front axle outboard joint shaft assembly groove.
| 3. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP |
![]() |
Install the front No. 2 axle outboard joint boot clamp onto the outboard joint boot and temporarily fold back the lever.
![]() |
Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work surface. Roll the outboard joint and fold the lever until a click sound can be heard.
| *1 | Deflector |
![]() | Weight |
![]() | Contact |
![]() | Roll |
![]() |
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
| 4. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
![]() |
Install the front axle outboard joint boot clamp onto the outboard joint boot and temporarily fold back the lever.
![]() |
Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.
| *a | Place the tip near the center of the lever. |
![]() |
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
| 5. INSTALL DRIVE SHAFT DAMPER (for RH Side) |
![]() |
Install the drive shaft damper onto the front axle outboard joint shaft assembly as shown in the illustration.
| *1 | Drive Shaft Damper Setting Clamp |
| *2 | Drive Shaft Damper |
| 6. INSTALL DRIVE SHAFT DAMPER SETTING CLAMP (for RH Side) |
Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.
for One Touch Type:
![]() |
Using a screwdriver, install a new drive shaft damper setting clamp as shown in the illustration.
| *A | for One Touch Type |
| *B | for Claw Engagement Type |
| *a | Claws |
for Claw Engagement Type:
Using needle-nose pliers, install a new drive shaft damper setting clamp as shown in the illustration.
| 7. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY |
![]() |
Install new parts onto the front axle outboard joint shaft assembly in the following order:
| *1 | Front Axle Inboard Joint Boot Clamp |
| *2 | Inboard Joint Boot |
| *3 | Front No. 2 Axle Inboard Joint Boot Clamp |
| *4 | Protective Tape |
![]() | Outboard Joint Side |
![]() | Inboard Joint Side |
Front axle inboard joint boot clamp
Inboard joint boot
Front No. 2 axle inboard joint boot clamp
Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.
Remove the protective tape.
![]() |
Align the matchmarks and install the tripod joint onto the front axle outboard joint shaft assembly as shown in the illustration.
| *a | Matchmark |
Using a brass bar and a hammer, install the tripod joint to the front axle outboard joint shaft assembly.
![]() |
Using a snap ring expander, install a new shaft snap ring to the front axle outboard joint shaft assembly.
Pack the front drive inboard joint assembly and inboard joint boot with grease.
![]() |
Align the matchmarks and install the front drive inboard joint assembly onto the front axle outboard joint shaft assembly.
| *a | Matchmark |
| 8. INSTALL INBOARD JOINT BOOT |
Install the inboard joint boot to the front drive inboard joint assembly.
| 9. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP |
Install the front axle inboard joint boot clamp onto the inboard joint boot.
for One Touch Type:
![]() |
Using a screwdriver, install the front axle inboard joint boot clamp.
for Claw Engagement Type:
![]() |
Using needle nose pliers, install the front axle inboard joint boot clamp.
| *a | Claws |
| 10. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP |
Install the boot clamp onto the inboard joint boot.
![]() |
Adjust dimension (A) until it is within the specified length.
| LH Side | RH Side |
| 562.1 mm (1.84 ft.) | 842.1 mm (2.76 ft.) |
for One Touch Type:
![]() |
Using a screwdriver, install the front No. 2 axle inboard joint boot clamp.
for Claw Engagement Type:
![]() |
Using needle nose pliers, install the front No. 2 axle inboard joint boot clamp.
| *a | Claws |
| 11. INSPECT FRONT DRIVE SHAFT ASSEMBLY |
![]() |
Check that there is no excessive play in the outboard joint.
Check that the inboard joint slides smoothly in the thrust direction.
Check that there is no excessive play in the radial directions of the inboard joint.
![]() |
Check the boots for damage.
| LH Side | RH Side |
| 562.1 mm (1.84 ft.) | 842.1 mm (2.76 ft.) |